Answered: A hollow steel shaft is transmitting 15…

A hollow steel shaft is transmitting 15 kW at 420 rpm. Calculate the thickness of the shaft where outside diameter is 50 mm and allowable shear stress acting in the shaft is 70 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: Consider a solid steel shaft with an allowable shearing stress of 58 MPa. Design the shaft to…

Q: A solid shaft is required to transmit 120 kW power at 200 rpm. Find the suitable diameter of the…

A: Power, P = 120 kW Speed, N = 200 rpm Tmax = 1.2Tmean Shear stress, = 70 N/mm2…

Q: The engine of a ship develops 440 kW and transmits the power by a horizontal propeller shaft which…

A: INTRODUCTION : When the circular shaft either hollow or solid is used to the power transmission, the…

Q: A motor driving a solid circular steel shaft transmits 40 kW of power at 500 rpm. If the diameter of…

Q: a steel shaft is 100 hp at a speed of 950 rpm. the shear stress is 8000 psi. what is the economical…

Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…

A: Given: Power transmitted by the shaft P=75kWSpeed of the shaft N=200rpmModulus of rigidity…

Q: 5.Find the diameter of the shaft required to obtain a safety factor of 2for a steel shaft with Sy =…

A: Given data: The safety factor for the design of the shaft is N = 2. The yield strength of the shaft…

Q: A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at…

Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…

Q: A solid steel shaft of 15m long is stressed at 32 MPa when twisted through 50.Using G =83Gpa…

Q: Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a…

A: Given: T =1200 NM G=78 GPa Allowable shear stress =40 MPa Allowable rate of twist 0.78/m TO…

Q: The driveshaft of an automobile is being designed to transmit 225 kW at 3239 rpm. Determine the…

Q: Define I) torque II) torsional loads b)A solid circular shaft is to transmit 80kw power at…

A: Torque is defined as moment of force acting about an axis which is cabable of producing angular…

Q: A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

Q: A Cast iron shaft transmits 30kW at 300 rpm. It carries a central load of 1000N and is simply…

Q: Find the max shear stress in given data of two circular shafts (S) AND (H)

A: GIVEN DATA; Two circular shaft made same material one solid and one hollow both have same length…

Q: 2. A 10-x 10-mm key was used in a 45-mm diameter shaft of a 30 kW diesel engine rotating at 1200…

Q: Calculate diameter of shaft using maximum shear stress theory,when equivalent torque of 800 x 103…

A: Given data: The allowable shear stress for the shaft is τ = 80 MPa. The equivalent torque is T =…

Q: A plat spiral spring is made of 6 mm wide.and 2.5 mm thick wire andis 250 cm long. Assuming the…

A: Given data: width of spring = 6 mm Thickness of wire = 2.5 mm length = 250 cm Maximum stress = 840…

Q: A motor is driving a solid circular steel shaft transmits 40kW of power at 500 rpm. If the diameter…

Q: A steel tube of outer diameter 86mm and inner diameter 52mm is under pure torsion. The diameter of a…

A: Outer diameter = 86 mm Inner diameter = 52 mm Answer is (B) 81.98 mm

Q: A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength…

A: Given Data⇒ Tensile load (F)=38 KN External diameter of the hollow tubular component is d2=45 mm…

Q: -) A hollow circular steel shaft has a 150 mm outer diameter, and a 100 mm inside diameter. The…

Q: The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

Q: A shaft of diameter 40 mm is subjected to 360 N-m torque. The length of the shaft is 10 cm.…

A: Given data: The diameter of the shaft, d = 40 mm. The torque subjected to the shaft, T = 360 N-m.…

Q: A hollow shaft has an inner diameter of 0.035 m and an outer diameter of 0.06 m. Compute for the…

Q: A hollow vertical cylindrical steel pipe with an outside diameter of 300 mm and 6 mm thick has a…

Q: Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm…

A: Given data T=92.7 N-mD=20 mmt=2 mmd=16 mm

Q: The driveshaft of an automobile is being designed to transmit 234 kw at 3167 rpm. Determine the…

Q: A hollow 3 m long steel shaft that will provide the main engine drive transmission for a ship to be…

A: Given data: Length of hollow steel shaft, L=3 m=3000 mm. Torque requirement is, T=25 kN.m=25×106…

Q: A solid circular shaft to transmit,80kw power at 200rpm.calculate the shaft diameter and strain…

Q: A hollow aluminum rod has a max shear stress of 0.075 GPa. What is the maximum torque that can be…

Q: A conveyor belt is driven by a 8-hp motor turning at 2,500 rpm. Through a series of gears that…

A: Given:Power of motor,P=8HP=(8×745.7)W=5965.6WSpeed of motor,N=2500rpmSpeed of belt drum motor…

Q: 6. A marine turbine developing 15,000 hp and it turns the shaft at 300 rpm. The propeller which is…

Q: A hollow nickel steel shaft with outside diameter is twice the inside diameter is to transmit 1492…

Q: A hollow steel shaft is to transmit 4,867 N-m of torque and is to be sized so that the torsional…

Q: A shaft is used to transmit 55 kW power at 500 rpm is subjected to a bending moment of 450 Nm.…

A: Given Data The power transmitted by the shaft is: P=55 kW=55000 W The rotation speed is: N=500 rpm…

Q: A solid 1.2 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

Q: A solid steel shaft 6 m long is stressed at 80 MPa when twisted through 8°. Using G= 83 GPa, compute…

A: Given data: Length of the shaft, L = 6 m. Maximum shear stress, τmax = 80 MPa. Twisting angle, Ɵ =…

Q: Q6: The engine of a ship develops 440 kW and transmits the power by a horizontal propeller shaft…

A: The engine of a ship develops 440 kW and transmits the power by a horizontal propeller shaft which…

Q: A motor drives 50 hp to a shafting 1 1/2 in. diameter and 3 ft. long. If the maximum shearing stress…

Q: A drilling riser is used to drill a 4km deep hole into the seabed. The riser can be approximated as…

A: Given. G= 89 Gpa , d_o = 185 mm d_i = 160 mm P= 230 Kw N= 75 rpm

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A hollow steel shaft is transmitting 15 kW at 420 rpm. Calculate the thickness of the shaft
where outside diameter is 50 mm and allowable shear stress acting in the shaft is 70 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.