Answered: Calculate the maximum and minimum shear…

Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: If a drive shaft with a shear modulus 120GN/m² and a length of 0.45m is to be subjected to a torque.…

Q: Calculate the maximum permissible torque on a hollow shaft if the maximum allowable shearing stress…

Q: A solid shaft having a diameter of 100mm has an allowable shearing stress of 80 MPa. Determine the…

Q: A hollow circular torsion member has an outside diameter of 22 mm and inside diameter of 18 mm, with…

A: GivenDo=22mmDi=18mmD=20mmτ=70MPa at mean diameterG=77.5GPa

Q: Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to…

A: GivenT=800 Nmd=50mm=0.05 mFormulaσT=16Tπd3

Q: A 2-in diameter steel shaft rotates at 150 rpm. If the shearing stress is limited to 10 ksi,…

Q: solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum…

A: for solution refer below images.

Q: A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at…

Q: A solid 38 mm diameter shaft is rotating at a speed of 510 rpm with a maximum shear stress of 78…

Q: PROBLEM 1. A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters…

Q: A solid circular shaft is required to transmit 200 kW while turning at 90 rpm (rev/min). The…

A: Consider a shaft having diameter 'D' is subjected to a twisting moment 'T'. Then, from torsion…

Q: Q3 A hollow shaft with an external diameter of 160 mm transmits a maximum torque of 16 kN.m. If…

Q: Compute the torsional shear stress that would be produced in a solid circular shaft having a…

Q: A shaft 100mm in diameter and 3 m long, with built-in ends, is subjected to a clockwise torque of 4…

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

Q: Design a hollow circular steel shaft to transmit an applied torque of 360,000 in-lbs. The allowable…

Q: A solid circular shaft of 35 mm diameter transmits a torque of 1460 Nm. The value of maximum shear…

A: Diameter of solid circular shaft, d = 35mm Torque transmitted, T = 1460 Nm or 1460000 Nmm

Q: A hollow shaft is to transmit 390 kW at 70 rpm. If the shear stress is not to exceed 45 MPa and the…

A: Diameter ratio, Di/Do=0.58 Di=0.58 x Do Power, P=390kW=390000 W Speed, N=70 r.p.m Max Torque,…

Q: Figure Q6 shows a circular shaft AB and a square shaft BC where it is fixed at C. а. Determine the…

Q: Calculate the maximum torsional shear stress that would develop in a solid circular shaft, having a…

A: Given Data : Diameter lf shaft(d)=32 mm=0.032 m Transmitted power(P)=95 KW Speed(N)=525 RPM

Q: To Tc B A If TB=3T and TC=1T, determine the maximum value of T considering that the maximum…

A: Given data: - The value of torque at C is TC = 1T. The value of torque at B is TB = 3T. The…

Q: 5.2 A hollow bronze shaft of 75 mm outside solid steel shaft of 50 mm diameter and of the same…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: aft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer…

A: Given:T=5.5 kN.mdo=0.1 mt=10 mm

Q: PROBLEM 1. A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters…

A: As per given question L=1.5m D1=40mm D2=60mm Modulus of rigidity =77gpa We have to determine a)…

Q: Calculate the unit shearing stress at the inner surface of a hollow shaft which D = 150 mm and d =…

Q: A carbon steel shaft AB is fixed with two gears and is applied with 4 torque as shown in Figure 1.…

Q: A steel marine propeller shaft 7 inches in diameter and 18 ft long is used to transmit 9,138 hp at…

A: Given data, d= 7 in L= 18 ft = 216 in G= 12*10⁶ psi P= 9138 HP N= 189 rpm

Q: shaft with a diameter of 50 mm and a length of 1300 mm with a safe shear yield strength of 20 N /…

A: Given:d=50 mml=130 mmSys=20 MPaT=565 NmG=80 GPa

Q: 3. Calculate the diameter of the shaft required to transmit 45 kw at 120 rpm. The maximum torque is…

A: Given Data: The power transmitted by the shaft is, P=45 kW=45 kW×1000 WkW=45000 W. The speed of the…

Q: A solid shaft 2 m. long is stressed 60 MPa when transmitted a power of 50 kW at 2 rev /…

A: Given: The length of solid shaft, L = 2 m The shear stress in shaft, τ = 60 MPa The transmitted…

Q: A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer…

Q: Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 240…

A: Given data: - The maximum shear stress on the circular shaft is τ = 240 MPa.

Q: steel shaft 8 ft long that has a diameter of 3 inches is subjected to a torque of 27 kip ft.…

Q: Two solid shafts, 50 mm in diameter, are connected by a flange coupling with six bolts and a pitch…

Q: A hollow brass alloy shaft with an outside radius of 50-mm and a wall thickness of 10-mm is…

A: Given data: ro=50 mmt=10 mmT=5.5 kN.m Need to determine the minimum required diameter in mm of a…

Q: A line shaft rotating at 55 RPS is to transmit 28 kW. The shaft may be assumed to be made of mild…

A: The given values are - P=28×103W , N60=55 rps, ζ=85 MPa P=T.ϖ where…

Q: Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed…

Q: A steel marine propeller shaft 14 in. in diameter and 18 ft long is used to transmit 5000 hp at 189…

A: Given data: Unit conversions used are:

Q: Figure 1 is presented the solid shaft AB rotates at 650 rpm and transmits 30 kW from the motor…

A: To find: The smallest permissible diameter of the shaft. Given: The speed of shaft AB is NAB=650…

Q: B) Estimate the minimum shaft diameter according to the maximum shear stress theory for a shaft…

Q: Engineering Mechanics problem. A solid circular steel shaft having an outside diameter of D = 0.75…

Q: Consider a solid shaft of 18-mm diameter. Determine the maximum shearing stress in the shaft as it…

Q: esign a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of…

A: Given: Hollow shaft,Power,P=80 kWspeed, N=4000 rpmangle of twist,θ=0.2oshear stress, τ=480…

Q: Pls answer thank you! The maximum shear stress induced on a 3” diameter solid shaft loaded with a…

Q: if you wrong i will dislike. A motor driving a solid circular steel shaft transmits 40 kW of power…

A: Given Data ⇒ Power transmitted by motor (P)=40 KWSpeed (N)=500 rpm Diameter of the shaft (d)=40…

Q: 5.2 A hollow bronze shaft of 75 mm outside diameter and 12.5 mm thick is coaxlal Willl d solid steel…

Q: Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the…

A: Given data: The power transmits, P = 45 kW. The speed of the shaft, N = 120 rpm. The permissible…

Q: What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3°…

Q: Torsion in circular shafts From the figure as shown, the maximum shearing stress is 30 MPa and the…

Q: A motor drives 50 hp to a shafting 1 1/2 in. diameter and 3 ft. long. If the maximum shearing stress…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
Determine the distribution of shear stress in the following circular shafts that are subject to a maximum torque of 7.5 Nm by calculating the polar second moment of area.
A hollow shaft for a rotary compressor is to be designed to transmit a maximum of torque of 4750 N-m. The shear stress in shaft, if the ratio of the inside to the outside diameter is 0.4
A solid shaft having a diameter of 100mm has an allowable shearing stress of 80 MPa. Determine the maximum torque in KN-m that the shaft can carry without exceeding the allowable shearing stress.
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?