Q1 A homogeneous disk of weight W-6 lb rotates at the constant rate w₁-22 rad/s with respect to arm ABC, which is welded to a shaftDCE rotating at the constant rate wy 11 rad/s. Determine the angular momentum H4 of the disk about its center ArohinD9mM12 mib-ft-s (b-ft-sThe angular momentum HA of the disk about its center A is HAnces

Answered: Image /qna-images/answer/6c002b6c-c9f5-4e8e-ac17-1d96253f3f7a.jpg

A homogeneous disk of weight W=6 lb rotates at the constant rate w-22 rad/s with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate w211 rad/s. Determine the angular momentum H4 of the disk about its center A rohin bas bfsj The angular momentum HA of the disk about its center A is HA

A homogeneous disk of weight W=6 lb rotates at the constant rate w-22 rad/s with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate w211 rad/s. Determine the angular momentum H4 of the disk about its center A rohin bas bfsj The angular momentum HA of the disk about its center A is HA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A homogeneous disk of weight W= 6 lb rotates at the constant rate W1= 16 rad/s with respect to arm ABC,which is welded to a shaft DCE rotating at the constant rate w 2= 8 rad/s. Determine the angular momentum HA of the disk about its center A.
A 1-m-long uniform slender bar AB has an angular velocity of 12 rad/s and its center of gravity has a velocity of 2 m/s as shown. About which point is the angular momentum of A smallest at this instant? P1 P2 P3 P4 It is the same about all the points.
A 10 kg , 0.5 m radius wheel is to rotate from rest to a speed of 100 rad/s in 5 s. Determine the tangential force ( N ) created at the rim of the wheel.
A 7.5 kg disk A radius of 0.6 m initially rotating clockwise at 300 rev/min is engaged with an 8.5 kg disk B of radius 0.4 m initially rotating counter clockwise at 700 rev/min, where the moment of inertia of a disk is given as I=1/2mr^2. Determine their combined angular speed (in rpm) and direction after the meshing of the two disks.
A homogeneous disk of mass m = 5 kg rotates at the constant rate w1 = 8 rad/s with respect to the bent axle ABC, which itself rotates at the constant rate w2, = 3 rad/s about the y axis. Determine the angular momentum HC of the disk about its center C.
A 7.5-kg disk A radius 0.6 m initially rotating clockwise at 300 rev/min is engaged with an 8.5-kg disk B radius 0.4 m initially rotating counter-clockwise at 700 rev/min, where the moment of inertia of a disk is given as I=1/2mr^2. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disk.
The rectangular plate, with a mass of 3 kg and a uniform small thickness, iswelded at the 45° angle to the vertical shaft, which rotates with the angular ve-locity of 20 rad/s. Determine the angular momentum of the plate about Oand find the kinetic energy of the plate. (Three-Dimensional Motion)
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
The double pulley shown in the figure has a mass of 3 kg and a radius of 100 mm rotation. Knowing that when the pulley is at rest, it is applied to the cable in B, a force P of magnitude equal to 24N, determine the speed of the center of the pulley after 1.5 s and the tensile force on cable C.
The uniform plate of mass m rotates about its corner O with the angularspeed ω. Determine the angular momentum of the plate about (a) the mass center;(b) the corner O; and (c) the corner A.
A locomotive consists of multi cylinder reciprocating engine running at a speed of 4 r.p.s having a stroke length of 27cm, which carries a mass of reciprocating part whose magnitude is 14kgs with a revolving part of 5kgs rotating at 16cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 520 from top dead centre to bottom dead centre. 1. Maximum primary unbalanced force of reciprocating mass in newtons ) 2. Balancing mass required at a radius of 44cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 74cm between the two cylinders in (N-m) 5. Magnitude…
A 1.6-kg tube AB can slide freely on rod DE which in turn can rotate freely in a horizontal plane. Initially the assembly is rotating with an angular velocity of magnitude w = 5 rad/s and the tube is held in position by a cord. The moment of inertia of the rod and bracket about the vertical axis of rotation is 0.30 kg.m2 and the centroidal moment of inertia of the tube about a vertical axis is 0.0025 kg.m2If the cord suddenly breaks, determine (a) the angular velocity of the assembly after the tube has moved to end E, (b) the energy lost during the plastic impact at E.