A homogenous 900 kg bar AB is supported at either end by a cable as shown. Calculate the following: a) Weight of bar b) Smallest area of each cable is the stress is not to exceed 100 Mpa in bronze and 160 Mpa in steel c) Determine the Axial force of each bar d) Calculate the Stress due to steel e) Calculate the Stress due to bronze STEEL =10 M BRONZE =7M 20 M Weight of bar = 800 x 9.81 = 7848 N OBr S 90 MPa = 90 x 10° Pa Ost S 120 MPa = 120 x 10° Pa Given: Given: Obr < 100 Mpa Ost <180 Mpa B.

A homogenous 900 kg bar AB is supported at either end by a cable as shown. Calculate the following: a) Weight of bar b) Smallest area of each cable is the stress is not to exceed 100 Mpa in bronze and 160 Mpa in steel c) Determine the Axial force of each bar d) Calculate the Stress due to steel e) Calculate the Stress due to bronze STEEL =10 M BRONZE =7M 20 M Weight of bar = 800 x 9.81 = 7848 N OBr S 90 MPa = 90 x 10° Pa Ost S 120 MPa = 120 x 10° Pa Given: Given: Obr < 100 Mpa Ost <180 Mpa B.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The global stresses in a three-ply laminate are given at the top and bottom surface of each ply in the tables below. Assume that each ply is 0.005 in. thick and the laminate has a top cross section of 4 in. × 4 in. What is the resultant force component Nx for the laminate in lb/in? What is the resultant force component Ny for the laminate in lb/in? What is the resultant force component Nxy for the laminate in lb/in?
A bronze tire (thickness=12mm, width= 110 mm, internal diameter=800 mm) was heated and shrunk onto an 800.5 mm diameter bronze wheel. E = 83 GPa. 1. Find the Tensile stress in the tire. a. 51.8 MPa b. 121 MPa c. 107 MPa d. 125 MPa 2. Find the compressive force bet the tire and the wheel when pinched. a. 1.56 MPa b. 3.53 MPa c. 2.25 MPa d. 3.75 MPa 3. Find the minimum required wheel thickness when allowable stress is 124 MPa and the compressive stress is 1.5MPa. a. 4.0 mm b. 4.25 mm c. 3.52 mm d. 4.84 mm
With a thick walled cyclinder the inner radius is 0.05m and out radius is 0.2m. The internal pressure is 200 MPa - What is the hoop and radial stress at the inner surface? - What would be a suitaable material for the cyclinder under von mises criterion?
Calculate the resulting stress in an aluminum wire, 4-m long and 2.6 mm in diameter, if a 12.5 -kg fixture is hung from the wire? Young's modulus for aluminum is 7.0 × 10^10 N/m^2. Express the answer in Pa and as a whole number.
For the steel block (Length L = 5-meter, Width W = 1 meter, Height H = 1 meter) with compression force on its cross-sectional side of (Your Student Id)N shown in following figure; a) Calculate Stress b) Calculate Strain when its length becomes L = 4 meter after applying force. c) Calculate of modulus of Elasticity. (Hint: If your ID is 114-2020, then compression force would be 114 N)
The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the design of AC only, if the allowable stress for the steel in this application is = 160 MPa, and the diameter of AC: d = 22 mm. Calculate the largest load p on AB in order to keep AC safe: pmax = ____ kN/m. Calculate your answer to 1 decimal place.
A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is 35cm and the steam pressure is 85N/mm².Assuming that the bolts are not initially stressed; find the size of bolts if the tensile stress is not to exceed 20N/mm²
The cross sectional area of the bar is 5cm^2 What is the stress in steel?
A sign of mass 2,500-Kg hangs from the bottom end of a vertical cylindrical aluminum bar (with a diameter of 12-cm). (a) What is the stress within the bar? (b) What is the bar’s strain? (c) If the bar is 10-m long, how much is it lengthened?
The femur, the long bone in the thigh, can be modeled as a tube of compact bone for most of its length. The cross-section area of the compact bone in the femur of a 70 kg person is 4.8 x 10-4 m2, a typical value.a. If this person supports his entire weight on one leg, what fraction of the tensile strength of the bone does this stress represent?b. By what fraction of its length does the femur shorten?
A 10m long beam is supported by a steel rod and a hinge shown below. The rod is 20mm in diameter and the beam supports a uniform load of 1a kN/m. The weight of the beam is (11 x 1000) kg. A. Find the stress on the steel rod in Mpa B. Find the diameter in mm of the pin at B to if the allowable stress in the pin is 210 MPa C. Find the maximum force (kN) that can be applied to a steel pipe attached vertically to a rigid support if the allowable stress in the pipe is 10MPa. The outside diameter is 155mm and a thickness of 12mm.