4. Give practical applications of wire ropes. What are the advantages of wire ropes? 5. What is the difference between block brakes with short and long shoes? 6. For the following wire rope diameters of 6 x 19 type wire rope, with steel core, find the approximate mass (self-weight) in kg/m from online resources. Wire rope diameter 'd' in mm 16 25 32 44 7. What are the various stresses induced in the wire rope?

4. Give practical applications of wire ropes. What are the advantages of wire ropes? 5. What is the difference between block brakes with short and long shoes? 6. For the following wire rope diameters of 6 x 19 type wire rope, with steel core, find the approximate mass (self-weight) in kg/m from online resources. Wire rope diameter 'd' in mm 16 25 32 44 7. What are the various stresses induced in the wire rope?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
Solve the problem below. For your final answer, use whole number. An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 42563-Nload, using the following data: length of steel = 1.56 m, length of bronze = 2.18 m Area of steel = 563 mm, Area of bronze = 233 mm Modulus of elasticity of steel = 193 Gpa, Modulus of elasticity of bronze = 82 Gpa x = 0.69 m, y = 1.03 m, and z = 0.79 m.
A spring leaf is made with an unknown material and has a width of 2.7 inches, a thickness of 5/16 inches, and a length of 1 yard. The leaf spring has 2 full-length leaves and 5 graduated leaves. For a load of 1.5 kN, the leaf spring deflects 115 mm. A.) Find the modulus of elasticity of the spring steel used in the leaf spring in ksi. B.) Using the modulus of elasticity, find the stress experienced by the material in MPa of the strain is 0.015. Answer in the Given-Required-Solution format. Show the unit analysis and the answer should be at least in 4 decimals. Subject: Machine Design
1. A non-uniform is 4.5m long and weighs 640N. It is balance when a 270N weight is hung 0.800m from the light end of the bar and the bar is pivoted at its center. Where is the center of gravity of the bar? 2.Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the steel rod caused by the 43091-Nload, using the following data: length of steel = 1.36 m, length of bronze = 2.08 m Area of steel = 562 mm, Area of bronze = 243 mm Modulus of elasticity of steel = 215 Gpa, Modulus of elasticity of bronze = 102 Gpa x = 0.63 m, y = 1.01 m, and z = 0.84 m.