A horizontal beam of length 2 m and mass 8.0 kg has a mass of 5.0 kg and width 0.8 m sitting at the end of the beam (see the following figure). What is the torque due to gravity (in N. m) on the beam-block system about the support at the wall? (Enter the magnitude.) Wall support 0.8 m, 5.0 kg 2 m, 8.0 kg

A horizontal beam of length 2 m and mass 8.0 kg has a mass of 5.0 kg and width 0.8 m sitting at the end of the beam (see the following figure). What is the torque due to gravity (in N. m) on the beam-block system about the support at the wall? (Enter the magnitude.) Wall support 0.8 m, 5.0 kg 2 m, 8.0 kg

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Rotational Dynamics

Section: Chapter Questions

Problem 8WUE: A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and...

See similar textbooks

Similar questions

What three factors affect the torque created by a force relative to a specific pivot point?
Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?
The fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22
Can a set of forces have a net force that is zero and a net torque that is not zero?
Can a single force produce a zero torque?
A constant torque is applied to a rigid body whose moment of inertia is 4.0kgm2 around the axis of rotation. If the wheel starts from rest and attains an angular velocity of 20.0 rad/s in 10.0 s, what is the applied torque?
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.
A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
Can a set of forces have a net torque that is zero and a net force that is not zero?
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P10.73 Problems 73 and 74.
A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and a second 1.00 m from the right end. Find the magnitude of the force exerted on the plank by the second pivot. (See Section 8.4.)