A horizontal curve is being designed around a pond with a tangent length of 800 ft and central angle of 0.6109 radians. If the PI is at station 85 + 00, determine the station of PT. A. 97 + 35 B. 92 + 50 C. 89 + 75 D. 101 + 45

A horizontal curve is being designed around a pond with a tangent length of 800 ft and central angle of 0.6109 radians. If the PI is at station 85 + 00, determine the station of PT. A. 97 + 35 B. 92 + 50 C. 89 + 75 D. 101 + 45

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter15: Geometric Design Of Highway Facilities

Section: Chapter Questions

Problem 7P

See similar textbooks

Related questions

Q: What diameter of a standard, sharp-edge orifice will be required to produce a discharge of 1.25 cfs…

Q: The beam is loaded and supported as shown. Determine the magnitude of the force P so that the slope…

Q: A steel beam supports a total UDL F, including its self-weight, of 70kN over a span L of 5.0 m. If…

Q: Oil with specific gravity of 0.88 flows through a pipe which changes from 6 in. at section A to 18…

Q: A = 5 Compute A? and A³. What will A" turn out to be?

Q: effect of crosslinks on an elastomer

A: Elastomers are loosely cross-linked polymers. They have the characteristics of rubber in terms of…

Q: Question 3 Calculate the pin reactions at E, D and C pins in the frame shown. 2 m 2 m E 3 m C 1.5 m…

Q: Replace the two forces acting on the post by a resultant force and couple moment at point O. Express…

A: A=8kB=6jC=6kD=2i-3jAB=6j-8kCD=2i-3j-6kFAB=5ABABFAB=56j-8k62+82=3j-4kFCD=6CDCDFCD=62i-3j-6k22+32+62=1…

Q: Sand lying below a masonry dam has a porosity of 40% and a specific gravity of 2.67, then the…

Q: 3. The CST element is loaded by pressure load p = const. Calculate the equivalent nodal forces. 3 p…

A: Given data- To Find- The equivalent nodal force.

Q: Block A has a weight of 60lb and Block B has a weight of 10lb. Determine the speed of Block A after…

Q: Determine the reactions at supports A and B of the frame. 7 kip 10 kip 5 kip -8 pies t 6 pies- 2 kip…

Q: The collapse load for the beam as shown in figure is to G. Mp Me -L'2 te L/2 L2 H L2

Q: Determine the relative angle of twist of gear D relative to gear A (in degrees). * Your answer What…

Q: The braking distance of a car from 120 km/h is 50 m assuming the pavement is level. (a) if the…

Q: Determine the member force CF

Q: Calculate the safe load over a compression member of unsupported length of 4.6 m. The member is to…

Q: SET P1, kN M1, W1, L1, L2, L3, L4, m X-Limit 1 X-Limit 2 kN.m kN/m A 70 150 15 2.50 Osx;<L2 L3<X2SL4…

Q: compare between cement and fine aggregate

A: ASKED: To compare between cement and fine aggregate. Given, CONCRETE MIX STRENGTH CEMENT (kg.m)…

Q: If P1=P2=P3= 69.69KN and each member has a diameter of 40mm, compute the deformation on members CD,…

A: Compression force cause decrease in menmber length and tension force causes increase in member…

Q: I. Calculate the safe concentrated live load at the free end for a rectangular cantilever beam 3 m…

Q: The two systems shown start from rest. On the left, two 40-lb weights are connected by an…

Q: TRIP DISTRIBUTION Complete the second iteration. The Jeffersonville Transportation Study Area has…

A: The planning, development, and operation of systems for moving products and people by roadway,…

Q: Find the value of change in length if strain is 0.0025 and original length is 20 m

A: The given question is related with solid mechanics . In this question we are provided with value of…

Q: The braking distance of a car from 90 km/h is 40 m assuming the pavement is level. (a) if the…

Q: Estimate for the concrete, formworks, reinforcement requirement of Beam GG-36. Length of Beam 1 =…

Q: Please round to the nearest One (i.e., 1). PLEASE DO NOT USE COMMA (S) ON YOUR ANSWER!!! Moist unit…

A: ASKED- To determine: Ultimate bearing capacity (qu) Allowable bearing capacity (qa) Given, Moist…

Q: Find the water content in the following calculations 1- Liquid limit Determination: Weight of can+…

Q: Determine tne volume of concrete of Girder G3 from grialine A/3-4 if there are 18 identical spans in…

Q: A concrete structure with a minimum dimension of 250 mm, concrete cover of 38mm, and rebar spacing…

Q: 1. Replace the two forces acting on the post by a resultant force and couple moment at point O.…

Q: A triangular, sharp crested weir with end contraction of 1.4 m long and the upstream depth is 2.35.…

Q: e shape factor for the section as shown -3d 3d - fe 2d

Q: 10 Cs C2 ► Ca L2 Each of the portal frame shown in the figure below has a tributary span of 6…

A: Wind Pressure: The total force exerted on a structure by wind is known as Wind Pressure.The…

Q: Three rods jointly support a 7kN load. Assuming that there was no stress in the rods before the load…

A: Given: The load is 7 kN. The length L is 2.75 m. The angles are 25o and 20o. The modulus of…

Q: If the friction force on the 6 kg object is 10 N. Find the coefficient of friction force ?

A: Given data : Friction force F=10 N Mass of object m=6 kg Acceleration due to gravity g=9.81 m/s2…

Q: A pipeline having a diameter of 200 mm consists 80 m cast iron pipe with 2 gate valves, 3-90° radius…

Q: Task 5 a C What is the displacement in place X? a = 0,4 m b = 0,22 m C = 0,25 m. M = 8 kNm E = 210…

Q: B C 3m A 30°

Q: Problem 1: Determine the magnitude of the resultant force per meter length acting on the…

Q: Sind the mexm Sherr streeY on the Ped Shown hor ziker 100 ら%/ 257 115 20 300 * oちm 3m 15 10 10

A: ASKED: To compute the maximum shear stress. The maximum shear stress in a beam section occurs at…

Q: A steel rod having a cross-sectional area of 332 mm^2 and a length of 176 m is suspended vertically…

Q: FLUID MECHANICS March 28th, 2022 Water at 60°C flows between two large flat plates. The lower plate…

Q: if the pavementis with 6 inclination, what will be the braking distance (in meter) of the car going…

Q: The tank shown in the accompanying figure is being filled by Pipes 1 and 2. If the water level is to…

A: For no change in water level in tank. The discharge entering the tank must be equal to discharge…

Q: The compression member 16-ft long is pinned at both ends and supported in the weak axis at the…

A: To select the lightest W14 section

Q: Find the design base shear for a 10-story steel special moment-resisting frame building, given the…

A: Formula to determine Design Base Shear is V= (CV*I/RT)W as per table 16-R URC 97 Cv for soil…

Q: A concrete spillway which is used to control a reservoir area of 4 hectares has a permanent crest…

Q: For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is…

Q: The compound shaft shown is attached to rigid supports. b. Bronze "B Steel For the bronze For the…

A: Given, SSbronze = 45 MPa SSsteel = 55 MPa

Concept explainers

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.

Question

A horizontal curve is being designed around a pond with a tangent length of 800 ft and central angle of 0.6109 radians. If the PI is at station 85 + 00, determine the station of PT.

A.

97 + 35

B.

92 + 50

C.

89 + 75

D.

101 + 45

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given a curve x^2+y^2+6x-12y+29=0. the location of the centroid from the y axis is equal to
Give me right solution with clear calculations. A certain horizontal curve has a central angle of 33.8°. If STA PI is 14+379 and STA PT is at 14+727, determine the station of PC.
A horizontal curve is being designed around a pond with a tangent length of 366 m and central angle of 0.52 radians. If the PI is at station 4+420, determine the station of PT.
A 7.15° horizontal curve has a central angle of 36.7°. If the station of PT is at 25+198, determine the station of PC.
A circular road is proposed to be laid out with tangent AB whose bearing is N85º54’E intersecting another tangent line BC whose bearing is N48º30’E. If the degree of the curve is 4.5º, using arc basis, determine the following: External distance, E Length of the road, LC If the station of point B 10+584, determine the station of PT.
Please Handwrite Answer! Horizontal highway curve: Given PI at 95 + 54.78, Δ = 24°28’, and D = 5°30’, compute thedeflections to the nearest second for the full stations (means stations 94+00, 95+00, 96+00, etc.)as well as for the beginning and end of the curve.
A 4.5-degree circular curve is to connect two tangent lines with a 55.5-degree external angle. The PI station is 25+30.25. Determine R, LC, T, E, PC station, and PT station.
Q#03: Two tangents AB & BC are intersected by a line having angles 40o & 35o respectively. The radius of 1st arc is 1000m and of 2nd arc is 800m. Carry out all the necessary calculation to find the chainage of tangent points points and the point of compound curvature given that the chainage of intersection point is 5000 m
The centerline of two parallel tracks are connected by a reversed curve. The angle of intersection of the first curve is 15 degrees and the distance between parallel tracks is 30m. If the radius of the second curve is 300m. a. Compute the length of the long chord from P.C. to P.T. ANS. 229.839m b. Compute the radius of the first curve. ANS. 580.432m please also include the drawing of the curve
What is the external distance of a simple curve of radius 91.44 m that connects two tangents which form anintersection angle of 74 0 46’36’’ note: pls show your complete solution
Provide illustration and complete solution. The azimuth from North of lines AB and BC are 330° and 25°, respectively. If a 5° simple curve is to be connected between these tangents and station of P.T. is at 28+525.69 m, find the elements of the curve.
A circular curve is formed by two intersecting line with length of 200 m forming an angle of intersection of 138⁰. The chainage of the beginning of curve is (100 + 12.500) and the peg interval is 20m. Calculate the different elements of the curve.