i need the answer quickly Find the water content in the following calculations1- Liquid limit Determination:Weight of can+Wet sample(gm)Weight of can+ Wetsample(gm)Weight ofWaterNumber ofTrial No.cancontentBlows(gm)0%(N)19.1322.5218.474133.1144.7640.945034116.91136.13129.432071.3787.1081.7123

we are required to find the water content in each trial. student must note that the 4th column is…

Find the water content in the following calculations 1- Liquid limit Determination: TT Weight of can+ Wet sample (gm) Weight of Water Weight of can+ Wet sample (gm) Number of Trial No. can content Blows (gm) (N) 1 9.13 22.52 18.47 41 33.11 44.76 40.94 50 3 4 116.91 136.13 129.43 20 71.37 87.10 81.71 23

Find the water content in the following calculations 1- Liquid limit Determination: TT Weight of can+ Wet sample (gm) Weight of Water Weight of can+ Wet sample (gm) Number of Trial No. can content Blows (gm) (N) 1 9.13 22.52 18.47 41 33.11 44.76 40.94 50 3 4 116.91 136.13 129.43 20 71.37 87.10 81.71 23

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A water sample was incubated at 20 °C for 3 days and its BOD3 concentration was found to be 150 mg/L. Given k20°c = 0.20/day (base e) and temperature coefficient for the rate constant is equal to 1.05. (a) BODultimate of this water sample=..............….mg/L (b) The BODs of this sample at 20 °C (in mg/L) =...……...... (c) kıs°c (in day-¹) mg/L.............. (d) The BODs of this sample at 15 °C (in mg/L) =...............
The 7 day BOD of a water sample was found to be 150 mg/lt. Determine the 5 day BOD of sample and take k=0.23/day.
The result of the liquid limit tests where N is the no of blows and w is the water content in % are given as follows: Trial 1 N=11 w=53.9; Trial 2 N=15 w=50.6; Trial 3 N=23 w=48.1; Trial 4 N= 30 w= 46; Trial 5 N= 46 w=43.3; Trial 6 N= 53 w=41. The PL= 25 and the in situ moisture content is 45%. Determine the liquidity index. a. 0.56 b. 0.91 c. 1.25 d. 0.59
The result of the liquid limit tests where N is the no of blows and w is the water content in % are given as follows: Trial 1 N=11 w=53.9; Trial 2 N=15 w=50.6; Trial 3 N=23 w=48.1; Trial 4 N= 30 w= 46; Trial 5 N= 46 w=43.3; Trial 6 N= 53 w=41. The PL= 30 and the in situ moisture content is 40%. Determine the liquidity index. a.0.56 b.0.59 c.0.91 d.1.25
Given:True volume = 2.76 mlBulk density = 1.86 g/mlBulk mass = 3.57 gUnknown: What is the flow characteristic of the sample? What is the bulk volume of the sample? What is the Hausner ratio? What is the Compressibility Index?
The hydraulic conductivity (K) of a homogeneous clay/sand mix aquifer is 2x10-4 cm/sec. The hydraulic gradient (groundwater surface slope) of the phreatic (water table) aquifer is 0.08 and the aquifer's effective porosity is 0.25. Calculate the average velocity of a conservative contaminant discharged to this groundwater unit. Enter your answer rounded to the nearest tenth in meters/year. Example: 5.2 , 65.7, 224.3 would all be proper forms of your answer
A settling column analysis is performed on a dilute suspension of particles from water. The suspension exhibited discrete particle settling characteristics. Data collected from samples taken at a depth of 1.5 meters are as follows: Time required to settle 1.5 m (min) 0.6 1.2 2.2 4.5 6 8.8 Fraction of Particles Settled 0.3 0.45 0.6 0.7 0.85 0.96 Plot the velocity distribution for the suspension Find the overflow rate (Q/A) for a settling tank that will give at least 75% removal. If the flowrate into the settling tank in part b. is 850 m3/hr, please give the dimensions of you settling tank? Since you will need to address the smaller particles that have passed through this system at some later point, what is the particle size distribution (mass fraction vs. diameter) if we assume the particle density is that of sand (sg = 2.65)
A permeameter of 8.2 cm diameter contains a sample of soil of length 35 cm. It can be used either for constant head or falling head tests. The standpipe used for the latter has a diameter of 2.5 cm. In the constant head test the loss of head was 116 cm measured on a length of 25 cm when the rate of flow was 2.73 ml/s. If a falling head test were then made on the same soil, how much time in seconds would be taken for thehead to fall from 150 to 100 cm ?
8. The result of the liquid limit tests where N is the no of blows and w is the water content in % are given as follows: Trial 1 N=11 w=53.9; Trial 2 N=15 w=50.6; Trial 3 N=23 w=48.1; Trial 4 N= 30 w= 46; Trial 5 N= 46 w=43.3; Trial 6 N= 53 w=41. The PL= 25 and the in situ moisture content is 45%. Determine the liquid limit. a.43 b.50 c. 47 d.41
Sample 2: Mass with empty mold M1 Mass of soil and mold M2 Hydraulic Head h Time interval t Volume V 145 g 250 g 950 mm 0.34 min 0.0046 L 145 g 260 g 900 mm 0.33 min 0.0049 L 145 g 228 g 922 mm 0.30 min 0.0051 L 145 g 281 g 915 mm 0.29 min 0.0044 L 145 g 219 g 908 mm 0.39 min 0.0042 L The diameter of the mold = 2.5 cm, Length of the sample = 0.3 m can u pls Find the permeability coefficient Mass of the soil Bulk Density Dry Density thank you Void Ratio
Please answer all 1. List the three corrections which should be applied to the hydrometer readings. 2. Why is it important to remove the hydrometer from the measuring cylinder between readings? 3. A hydrometer test has the following results; Gs = 2.70, temperature = 240C, and L = 92 mm at 60 minutes after the start of sedimentation. Calculate the diameter of the smallest-size particles that have settled beyond the zone of measurement at that time (use the table in the lab manual to find, A=0.0128). D(mm) = A sqrt( L(cm) / t(min) )
The soil sample presented in Figure below is under constant head permeability test. The soil is consist of a silty sand (SM) with k = 5×10-3cm/s and specific gravity of 2.70. The soil is fully saturated and its moisture content is determined to be 18.5%. Determine the time required for the plug of colored water to pass through the soil (i.e., from when the leading edge first enters the soil to when it begins to exit). Use seepage velocity for your calculation.