A horizontal rigid bar of negligible mass is binged at one end, Fig.1, and supported by a bronze rod 2m long and a steel rod Im long. A load of 50 kN is applied at the free end. Find the stresses developed in each rod. The areas and moduli of elasticity are given below. Steel 600 Bronze 300 Area(mm') E(GPa) 200 83 Bronze 2m Steel Im to 0.6m 1.0m 0.8m 50 kN

A horizontal rigid bar of negligible mass is binged at one end, Fig.1, and supported by a bronze rod 2m long and a steel rod Im long. A load of 50 kN is applied at the free end. Find the stresses developed in each rod. The areas and moduli of elasticity are given below. Steel 600 Bronze 300 Area(mm') E(GPa) 200 83 Bronze 2m Steel Im to 0.6m 1.0m 0.8m 50 kN

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Similar questions

The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
A ngid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D. as shown Neglect deflections of the bar due to bending Use E200 GPa What is the displacement of the loaded end of the bar? 2 Determine the tensile stress induced in rod CD by the 80 kN load the alowable stress in rod CD is 124 MPa, what weight W can be safely applied?
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to aodal loads as shown. If P-7 IN, Determine the total aodal deformation (in mm). Indicate negative sign f comoression. @ 5P O 3P E-200 6P 30 mm emm 80 mm 30 mn 30 mm
The member shown in the right side consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the largest value of P that meets the following design criteria: (i) the overall length of the member is not to change by more than 4 mm; and (ii) the stresses are not to exceed 148 MPa in steel and 110 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze. T 1.0 m 2m 3P A Steel A=480 mm² B Bronze A=650 mm² C 2P
The C83400-red-brass rod AB and 2014-T6-aluminum rod BC are joined at the collar B and fixed connected at their ends. The cross-sectional area of each member is 1.75 in² (Figure 1) Figure 1 of 1 3 ft 2 ft If there is no load in the members when T₁ = 50°F, determine the average normal stress in the member AB when T₂ = 110 °F. Express your answer to three significant figures and include the appropriate units. Obr = Submit Jal = Submit Part C μA Value Part B If there is no load in the members when T₁ = 50°F, determine the average normal stress in the member BC when T₂ = 110 °F. Express your answer to three significant figures and include the appropriate units. dB = My Answers Give Up O μA Value Units My Answers Give Up μA Units Also, how far will the collar be displaced? Express your answer to three significant figures and include the appropriate units. Value ? Units ? ?
Q4) A cast iron beam is of I – section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. I 80 mm- 20 mm 3 169.34 mm 200 mm 2) 20 mm A 90.66 mm 40 mm 100 mm Figure (3)
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 O Steel 1.5 m 1.0 m- 2.5 m 9. Determine the stress at the steel rod in MPa when there is a temperature rise of AT = 36 °C. W Bronze 3 m 1.5 m-
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m