10 mm 5 KN-m 40 mm 5 KN-m 150 mm 15 mm 120 mm Determine (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at points H and K. State whether the normal stress is tension or compression. (c) the maximum bending stress produced in the cross section. State whether the stress is tension or compression.

10 mm 5 KN-m 40 mm 5 KN-m 150 mm 15 mm 120 mm Determine (a) the centroid location, the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at points H and K. State whether the normal stress is tension or compression. (c) the maximum bending stress produced in the cross section. State whether the stress is tension or compression.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Very very Urgent The distributed load q and the singular moment M act on the stepped shaft given in the figure. Draw the cross-sectional influence diagrams of the system under these forces. Determine the maximum stress value for the critical section. L1 = 226 mm ,L2 = 118 mm, a = 159 mm M = 572 N.m, q = 5 N/mm D = 51 mm , d1 = 19mm , d2 = 5 mm
A hollow shaft shown with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 75 kN and torques TB = 16 kN-m and TC = 7 kN-m. 14. Calculate the polar moment of inertia of the section in mm4.1 15. Calculate the absolute value of the internal torque at H in kN.m. 16. Calculate the torsional shear stress at H in MPa. 17. Calculate the absolute value of the minor principal stress at point H in MPa. 18. Calculate the absolute value of the major principal stress at point H in MPa. 19. Calculate the absolute value of the maximum shear stress at point H in MPa. 20. Calculate the orientation of the principal axes in degrees. Kindly answer all numbers with complete solution
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
4. An aerial copper wire (E =1x 10 5 N/mm ^2) 40 m long has cross sectional area of80 mm2 and weighs 0.6 N per meter run. If the wire is suspended vertically, calculatethe maximum weight which this wire can support at its lower end if the limiting valueof stress is 65 N/mm 2.a. 4627 Nb. 4281 NC. 4519 Nd. 5188 N
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
The magnitude if the bending moment acting o the circular cross-section of a beam is M=30 000 lb-ft. A. Calculate the bending stress at point A. Choices: 9.07ksi,7.68ksi,10.48ksi,11.36ksi, B.Calculate the bending stress at point B Choices: 9.07ksi,7.68ksi,10.48ksi,11.36ksi C.Calculate the bending stress at point C Choices: 9.07ksi,7.68ksi,10.48ksi,11.36ksi
g.) What is the moment of inertia (I) about the neutral axis of the section? (in mm^4) h.)What is the first moment of an area (Q) about the neutral axis of the section? (in mm^3) i.)What is the maximum shearing stress (fv) of the beam? (in MPa)
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm
The single rope of a cantilever crane supports a load of 200 kN and passes over two pulleys and then vertically down the axis of the crane to the hoisting apparatus. The section AB of the crane is a hollow rectangle. The outside dimensions are 37.5 cm and 75 cm and the material is 2.5 cm thick all round, and the longer dimension is in the direction AB. Calculate the maximum tensile and compressive stresses set up in the section, and locate the position of the neutral axis. (Cambridge) ANSWER: tensile 155 MN/m2, compressive 147 MN/m2; neutral axis 0.365 m from outside of box-section Please show the solution to get the answer.
A structure is supported by braces each of which transfersa load P = 160 kips to the base of a column as shown in figure. A cap plate at the bottom of the brace distributesthe load P to four flange plates through a pin to twogusset plates. Diameter of Pin and thickness of flangeplate and gusset plate are provided in figure. Determine(a) The average shear stress in the pin.(b) The average bearing stress between the flange plates andthe pin.(c) The normal axial stress in gusset plate. Assume thatgusset plate is 4 inch wide
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?