Steel bar having a rectangular cross section 15mmx20mm and Sm long is suspended vertically from one end. The steel has a unit mass of 7850 kg/cu.m. and E=200GPA. If the load of 20KN is suspended at the other end of the rod, determine the total elongation of the rod. *

Steel bar having a rectangular cross section 15mmx20mm and Sm long is suspended vertically from one end. The steel has a unit mass of 7850 kg/cu.m. and E=200GPA. If the load of 20KN is suspended at the other end of the rod, determine the total elongation of the rod. *

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 125 kN 125 kN (1) 4.2 m 175 kN 175 kN B (2) 5.0 m A The roof and second floor of a building are…

A: Thank you for the question . As per code we are allowed to answer three subparts at a time so we are…

Q: A post having a hollow, circular cross section supports a P = 3.5 kN load acting at the end of an…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is…

Q: 3. For the force system shown P= 15KN T= 40 KN (3.9) F.30 KN in the figure determine the horizontal…

Q: A rectangular bar of length L has a slot in the central half of its length. The bar has width b,…

A: Given Data : L=400 mm b=51 mm t=11 mm E= 64 GPa P= 32 kN

Q: To determine the reaction forces at supports on a horizontal beam by using the equations of…

Q: The 25-kg flowerpot is supported at A by the three cords. Determine the force acting in each cord…

A: The given data is shown below:

Q: 3. Refer to the figure below, a kN/m W/5, m Beam Properties: | = 198 x 106 mm4 E = 200 GPa Rod…

A: Given data Rod properties Diameter of rod =12 mm Young's Modulus of rod material E =200 Gpa Beam…

Q: A rigid bar is suspended by three rods made of the same material as shown in the figure. The area…

Q: 1. The resultant of four forces of which 3 are shown in the figure is a clockwise 480 lb-ft couple.…

A: Draw the figure. Let F4 be the fourth force.

Q: The steel bars AB and BC are pinned at each end and support the load 200 kN as shown in the figure.…

Q: The pipe has an applied force of 2000 N. 5 m B F= 2000 N A 12 m 7 m y 3 m 10 m a. Express the 2000 N…

A: Given: The applied force is 2000 N. Consider the figure,

Q: Calculate for the axial force in kN at member HG of the frame shown in figure 2 using cantilever…

Q: 3. The 25-kg flowerpot is supported at A by the three cords. Determine the force acting in each…

Q: Replace the system of forces acting on the frame as shown by a resultant R at A and a couple acting…

Q: From the figure shown below, the length of member AB is 8m and member AC is 5m. If force F is 360N,…

Q: in the figure 9, assume clockwise moments as positive, force F= 432KN and force P =500 KN. Compute…

Q: 4) Obtain the reaction forces of the beam given below. The beam below is called Gerber beam (G¡ and…

A: FBD segment G2 (1)Σ MG2 = 08 x 4 - RF x 2 = 0RF = 16 KN ↑ FBD of segment G1 G2Σ MG2 = 0RC x 2 - 2…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Steel bar having a rectangular cross section 15mmx20mm and 11 m long is suspended vertically from…

A: Consider the free body diagram as;

Q: 1-m D.IS-m 0.25-m 0.15-m² 0. 25-m 1-m 0.75-m 0.15-m Figure 2 A T-beam with drawn x and y axes is…

Q: Determine the displacement of point B of the steel beam shown in Figure. Take E = 200 GPa, / =…

Q: The forces F1={−5i+4j−4k}kN and F2={5i−3j−2k}kN act on the end of the beam. Replace these forces by…

A: Given DataF1=-5i+4j-4kKNF2=5i-3j-2k KNNowFR=Resultant…

Q: In the figure 9, assume clockwise moments as positive, force F= 432KN and force P =500 KN. Compute…

Q: 2. Determine the horizontal force P in the figure to start the 400 lb wedge (a) moving to tl ight…

A: Solution: Given Data: W1=400 lbW2=2000 lbAngle of friction=20°

Q: 2) The rigid bar is supported by two wooden posts and a spring as shown in the figure. If each of…

Q: The rigid bar BC shown is supported by the steel rod AC of the cross-sectional area of 0.25in^2.…

A: Given: The cross-sectional area of steel rod AC is 0.25 in2. Consider the figure,

Q: 2. The vertical steel bars BE and CF supports the horizontal rigid bar ABCD and the applied forces…

Q: Solve for the horizontal components of the force at pin B (See the Figure below). 3' 6' 5' 3' A 8' E…

A: To determine the horizontal component of reaction at B. In order to determine the reaction at pin…

Q: 4. 4 point E having A shown in the figure has coordinates (6,4) determine coordinates (12.22) A(6.4)…

A: The Moment of a force is a measure of its tendency to cause a body to rotate about a specific point…

Q: Determine the member force CD(kN) in the figure shown. n十"十十* 1十十 50 AN 30 AN to

A: To find :- member force CD in kN of the truss shown in the question figure.

Q: For the beam in the figure; a) Find the coordinates of the geometric center and the moments of…

A: Draw the figure.

Q: 2. Resolve the 3Olb force into components along the u and v axes. 30 lb 15° \30°

A: To resolve 30lb force into components along u and v axes

Q: 4.165 Calculate the forces in members AB and DE. E D 8 kN A C 12 kN 1.5 m 2.5 m 2.5 m 1.5 m Figure…

Q: Question 2 [Soalan 2] a) Determine the shear force and bending moment of the wooden beam in Figure…

Q: Analyze the given frame. P units in kN/m

A: Given- a truss carrying UDL. Required- to find the unknown reactions.

Q: Calculate for the Moment in kN-m at member KH in kN-m at joint K of the frame shown in figure 1…

A: Given data:

Q: Find the maximum moment of the given load train at point n on the beam given in the figure? (Single…

A: Influence line diagram is the simplest method for finding the reaction and forces for the any…

Q: If the 580-kg drum has a center of mass at point G, determine the horizontal component of force…

A: Given Data -

Q: If the vertical component of the force F applied to the ring is 10 lb, determine the magnitude F and…

Q: 5. Determine the resultant and its distance from point A of the parallel force system acting on beam…

Q: Determine the horizontal component of the force applied by the smooth circular guide on the mass A.…

A: Hi

Q: please help on the question in the photo

Q: Determine the force in each member of the structure and establish whether the members are in tension…

A: Internal forces Because truss members are only subjected to tensile or compressive forces along…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Q.2 point A as shown in Figure? Find the moment of force about A 10 m B 90° 8 m 1000 KN 20- C

A: Given:- The magnitude of the force = 1000 kN The angle made by the force at point C = 20° To…

Q: Rigid 40° B 8 ft 2000 lb (a) The rigid bar BC in the figure is supported by the steel rod AC of…

Q: A rigid bar is suspended by three rods made the same material as shown in the figure. The area and…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Question

S=25

Steel bar having a
rectangular cross section
15mmx20mm and S m long
is suspended vertically from
one end. The steel has a unit
mass of 7850 kg/cu.m. and
E=200GPA. If the load of
20kN is suspended at the
other end of the rod,
determine the total
elongation of the rod.
Your answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

write down the given data

VIEW

Determination of total elongation

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Take F2=450 lb . DETERMINE RESULTANT FORCE
you did not use the correct value, a=5m and b= 2m, also, the force is q =5.1kn/m and not 5.3 kn/m can you do it with the right value please, or explain step by step without wrong value
A cantilever beam shown in Figure B2 is applied with point load of 10KN and pointmoment of 7KNm. By using Macaulay method:Sebuah rasuk terjulur dikenakan beban tumpu 10KN dan moment lentur 7KNmseperti yang ditunjukkan dalam Rajah B2. Dengan menggunakan kaedah Macaulay:i) Derive the moment equation for the beam Terbitkan persamaan momen bagi rasuk
Determine the intensity of the external dead load D? the reinforced concrete beam shown in the figure canresist. Consider the known self-weight of the beam as part of the dead load. Density of the reinforced con-cretd = 120 lbf/in3. Assume that the service dead load D? (not self-weight) and live load L are equal (D? =L); f ’c = 5,000 lbf/in2, fy = 50,000 lbf/in2. Apply Load Combo 2 only (1.2D + 1.6L). Exploit the instructorspreadsheet calculator posted in D2L to speed up the numerical calculations.
# = poundsa) what is the shear force at 5' rt. of A? (in pounds, 2 decimal places)b) what is the bending moment at 5' rt. of A? (in pounds, 2 decimal places)
Calculate the member force on member HF in Kips? Specify if T or C. 87.6 C 105.9 C 79.7 C 97.5 C 112.1 C
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
A = 3 B = 4 C = 1 D = 0 kindly answer the magnitude and if possible the forces
Steel bar having a rectangular cross section 15mmx20mm and 11 m long is suspended vertically from one end. The steel has a unit mass of 7850 kg/cu.m. and E=200GPa. If the load of 20kN is suspended at the other end of the rod, determine the total elongation of the rod.
Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of the 5-kip load. Follow the sign convention. a) Determine the normal force at point E. Express your answer in kilopounds to three significant figures. b) Determine the shear force at point E. Express your answer in kilopounds to three significant figures. c) Determine the moment at point E. Express your answer in kilopound-feet to three significant figures.
in th net force direction what is W(H) supposed to be and how did it get there? I know its the voloume but I don't undertsand why its in the equation
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa