(a) How much work is required to compress 5.06 mol of air at 20.9°C and 1.00 atm to one-ninth of the original volume by an isothermal process? kJ (b) How much work is required to produce the same compression in an adiabatic process? kJ (c) What is the final pressure in part (a)? atm (d) What is the final pressure in part (b)? atm

(a) How much work is required to compress 5.06 mol of air at 20.9°C and 1.00 atm to one-ninth of the original volume by an isothermal process? kJ (b) How much work is required to produce the same compression in an adiabatic process? kJ (c) What is the final pressure in part (a)? atm (d) What is the final pressure in part (b)? atm

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter21: The Kinetic Theory Of Gases

Section: Chapter Questions

Problem 21.28P: How much work is required to compress 5.00 mol of air at 20.0C and 1.00 atm to one-tenth of the...

See similar textbooks

Similar questions

A car tile contains 0.0380 m3 of air at a pressure of 2.20105 Pa (about 32 psi). How much more internal energy does this gas have than the same volume has at zero gauge pressure (which is equivalent to normal atmospheric pressure)?
An ideal gas initially at 300 K undergoes an isobaric expansion at 2.50 kPa. If the volume increases from 1.00 m3 to 3.00 m3 and 12.5 kJ is transferred to the gas by heat, what are (a) the change in its internal energy and (b) its final temperature?
The energy input to an engine is 3.00 times greater than the work it performs. (i) What is its thermal efficiency? (a) 3.00 (b) 1.00 (c) 0.333 (d) impossible to determine (ii) What fraction of the energy input is expelled to the cold reservoir? (a) 0.333 (b) 0.667 (c) 1.00 (d) impossible to determine
Two moles of a monatomic ideal gas such as oxygen is compressed adiabatically and reversibly from a state (3 atm, 5 L) to a state with a pressure of 4 atm. (a) Find the volume and temperature of the final state. (b) Find the temperature of the initial state. (c) Find work done by the gas in the process. (d) Find the change in internal energy in the process. Assume Cv=5R and Cp=Cv+R for the diatomic ideal gas in the conditions given.
How much work is required to compress 5.00 mol of air at 20.0C and 1.00 atm to one-tenth of the original volume (a) by an isothermal process? (b) What If? How much work is required to produce the same compression in an adiabatic process? (c) What is the final pressure in part (a)? (d) What is the final pressure in part (b)?
Which of the following is true for the entropy change of a system that undergoes a reversible, adiabatic process? (a) S 0 (b) S = 0 (c) S 0
In an adiabatic process, oxygen gas in a container is compressed along a path that can be described by the following pressure in atm as a function of volume V, with V0=1L:P=(3.0atm)(V/V)1.2 . The initial and final volumes during the process were 2 L and 1.5 L, respectively. Find the amount of work done on the gas.
A multicylinder gasoline engine in an airplane, operating at 2.50 103 rev/min, takes in energy 7.89 103 J and exhausts 4.58 103 J for each revolution of the crankshaft. (a) How many liters of fuel does it consume in 1.00 h of operation if the heat of combustion of the fuel is equal to 4.03 107 J/L? (b) What is the mechanical power output of the engine? Ignore friction and express the answer in horsepower. (c) What is the torque exerted by the crankshaft on the load? (d) What power must the exhaust and cooling system transfer out of the engine?
In a diesel engine, the fuel is ignited without a spark plug. Instead, air in a cylinder is compressed adiabatically to a temperature above the ignition temperature of the fuel; at the point of maximum compression, the fuel is injected into the cylinder. Suppose that air at 20 C is taken into the cylinder at a volume V1 and then compressed adiabatically and quasi-statically to a temperature of 600 C and a volume V2 . If =1.4 , what is the ratio V1/V2 ? (Note: static. In an operating diesel engine, the compression is not quasi-
During the compression stroke of a certain gasoline engine, the pressure increases from 1.00 atm to 20.0 atm. If the process is adiabatic and the air–fuel mixture behaves as a diatomic ideal gas, (a) by what factor does the volume change and (b) by what factor does the temperature change? Assuming the compression starts with 0.016 0 mol of gas at 27.0°C, find the values of (c) Q, (d) ΔEint, and (e) W that characterize the process.
During real expansion and compression processes in piston cylinder devices, it has been observed that gases satisfy the relationship PVn = C, where n and C are constant. Calculate the work done when a gas expands from 350 kPa and 0.03 m3, to a final volume of 0.2 m3, for the case where n = 1.5.