A hydraulic cylinder filled with water has an inside diameter of 1.0 in and a length of 2.0 ft. How many pounds of force must be applied to a piston at the end of the cylinder to compress the water by 0.1 in? Take the bulk modulus of water to be K=312,000 psi.

A hydraulic cylinder filled with water has an inside diameter of 1.0 in and a length of 2.0 ft. How many pounds of force must be applied to a piston at the end of the cylinder to compress the water by 0.1 in? Take the bulk modulus of water to be K=312,000 psi.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Related questions

Q: A tank is filled with fluid under pressure and the pressure gauge fixed at the top indicates a…

Q: What is the volume change in cm´ of a hydraulic oil when subjected to a pressure of magnitude 6 MPa?…

Q: A0.30m diameter cylinder A that weighs 100kN is suspended by a cord and rests against a smooth…

A: To calculate the Tension in the cord, and the reaction at the surface of the wall, we must apply- 1.…

Q: The clear plastic bottles used for carbonated beverages (sometimes also called "soda," "pop," or…

Q: An outside pressure 14.59 psi exist outside the small drop of water having a diameter of radius of…

Q: 2. A tank that weighs 5kg is filled with 3 liquids shown below. What is the force at the bottom of…

Q: An infinitely long cylindrical container has a cross section area of radius R, and is placed…

A: Pressure is caused by the force pressing on an area, according to physics. The weight operating on a…

Q: A: Figure (1) shows an open-water tank has two rectangular gates. If the density is 1000 kg gates is…

A: Givenρ=1000 kg/m3w=1.5m

Q: The tank of an air compressor has a volume of 2m3 and is filled with air at a temperature of 40…

Q: The test tube opens at 293 K with 13 cm Hg at the bottom, and 5.6 cm water above Hg. Calculate the…

Q: he clear plastic bottles used for carbonated beverages (sometimes also called “soda,” “pop,” or…

A: Given Inside pressure = 570 kPa Outside pressure = 7 kPa Permeability Constant bottle = 0.23 x 10-13…

Q: odulus of 1kg of water is 2.2 GPa. If the percentage reduction in volume is 6%, determine the…

Q: When a liquid of volume 4 liter is subjected to an additional pressure of 5 x 107 N/m2, the change…

Q: The power 395 W is required to transmit 5 x 10-3 m3/s of water. Find the loss of head due to…

A: P=ρgQH

Q: A copper cube of 200 mm side length is suspended by a string in oil and water as shown in figure.…

A: To find: The tension developed in the string. Given: The length of copper cube is a=200 mm1 m1000…

Q: 2. An automobile and its load weigh 22.5 KN and the center of gravity is 0.60 m above ground level…

A: Given , Weight of the car , W =22.5 KN Initial velocity of car , U = 96.5 Km/hr = 26.66m/s Final…

Q: 1. A building is 512 m high. What must be the minimum water pressure (psi) in a pipe at ground level…

A: As per guidelines i can solve only 1st question. Given data; height = 512 m Neglect friction loss…

Q: (a) Find the buoyant force acting on the balloon, assuming the density of air is 1.29 kg/m3. kN…

A: The radius of the spherical weather balloon r=3.10 m The total mass of the balloon m=22.0 kg The…

Q: Water flowing at 1.0 ft/s in a pipe passes into a constriction where area is one-tenth the normal…

A: V'=1.0 ft/sρ=62.4 lbs/ft3A'=110A P-Pressure of Normal pipe P'-Pressure of given pipe

Q: In the figure, an open tank contains a layer of oil floating on top of a layer of water (of density…

A: Givenρw=Density of water=1000 kg/m3ρo=510 kg/m3hw=3 mPressure=P=5×104PaPart aHere according to given…

Q: 9. The density of saturated vapor refrigerant -134a is expression in the form p= aT + bT +c, (where…

A: Given data :- T1= -15°C , P1= 164kpa T2 = 60 °C , P2 =1683kpa

Q: The piston shown (Figure 1) is acting on a fluid whose pressure is P = 135 kPa (abs). What force, F,…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Determine the pressure difference between the inside and outside of the 0.11 mm diameter air bublle…

A: Diameter of bubble, d=0.11 mm =0.11 *10-3 mSurface tension at the air-liquid interface, σ=0.106 N/m

Q: It is required to determine the maximum force FT required to hold the inflatable flood control…

A: Given: P=12000 Pad=950 mmL=12 m= 12000 mmt=2.5 mm

Q: The complex air tank AB has an inner diameter of 450 mm and a uniform wall thickness of 6-mm and the…

Q: depth of an oil well is 17,500 feet. The pressure of the oil at the bottom is the same as that of a…

A: Given:hoil=17,500 fthwater=15,500 ftρoil=55 lbm/ft3ρwater=63.9 lbm/ft3

Q: A cylinder weighing 445 N and having a diameter of 1 m floats in salt water (sp.gr. 1.03)…

A: Given: Weight of the cylinder is 445 N. Diameter of the cylinder is 1 m. Specific gravity of the…

Q: A thin-walled cylindrical pressure vessel has a diameter of 1.7 metres and contains gas at a…

Q: A concrete dam has the profile shown in figure 4. The dam retains water that is 10 m deep and 5 m…

A: This question is from fluid mechanics. We have to find hydrostatic thrust. Given density of water…

Q: Q1/ A piston pushes down on a volume of hydraulic oil ISO 68, trapped in a cylinder, its bore is…

Q: A hydraulic lift is to be used to lift a 2500 kg weight by putting a weight of 25 kg on a piston…

A: Given Data Lift weight is 2500Kg weight on piston = 25Kg Diameter of piston is D1 = 10cm Diameter…

Q: Determine the total force in kN on a circular plate of diameter 1.5 m which is placed vertically in…

A: Diameter of circular plate, d = 1.5 m Center of the plate from free surface of the water, h' = 2 m

Q: The clear plastic bottles used for carbonated beverages (sometimes also called “soda,” “pop,” or…

A: To Find : The shelf life in days for a bottle of pop . Given : The 20-oz bottle of pop has a CO2…

Q: A pipe is horizontal and carries oil that has a viscosity of 0.14 Pa s. The volume flow rate of the…

A: Given Viscosity = 0.14 Pa. s Flow rate, Q = 5.3 × 10-5 m3/s Radius, R =…

Q: 2. Find the angle that the surface tension film leaves the glass for a vertical tube immersed in…

Q: relation to the figure shown, the liquid is water (p = 1000 kg / m3). The gate is rectangular and…

Q: A 601.7 mL sample of oil is subjected to a pressure increase of 9.2 MPa due to a piston, which…

Q: Determine the pressure difference between the inside and outside of the 0.13 mm diameter air bublle…

Q: 5. Determine (i) density, (ii) weight density, and (iii) specific volume at a depth of 8000m from…

A: (i) Density: 1055.2 kg/m3 (ii) Weight Density: 10351.512 N/m3 (iii) Specific Volume: 9.477 × 10-4…

Q: containing Oxygen (initially at sea level) has a diameter of 8in. If the uniform density of air is…

Q: The bulk modulus of water is found to be 2.2 GPa. What is the pressure required to reduce its volume…

Q: 9. The density of saturated vapor refrigerant -134a is expression in the form p= aT + bT + c, (where…

A: Given data:- T1= -15°C T2 = 60°C P1=164 kpa P2=1683kpa

Q: In a hot air balloon launch, it was known that the material used in the construction amounts to…

Q: Determine the pressure difference between the inside and outside of the 0.11 mm diameter air bublle…

Q: A cylindrical object with a mass of m = 4.65 lbm slides into a pipe downward. The object has a…

A: Given: The mass of object, m = 4.65 lbm The diameter of object, d = 8.4 in The height, h = 9.9 in…

Q: 4.) A 1.8 m diameter closed cylinder, 2.7 m high is completely filled with glycerin having sp. gr.…

A: 4.) A 1.8 m diameter closed cylinder, 2.7 m high is completely filled with glycerin having sp. gr.…

Q: air and has a volume of 2.5 x103 m³. The weight of the rock when submerged

Q: An underwater pipeline must be laid 40 meters deep. The density of sea water is 1 025 kg/m³. The…

A: Solution.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
2. A spherical balloon containing Oxygen (initially at sea level) has a diameter of 8in. If the uniform density of air is 0.07498lb/ft3 and that the pressure at sea level is 14.7psia, determine the new diameter (inch) of the balloon if it has been brought above sea level by 6000ft. Draw a figure or FBD that will support the problem. Explain each step by step formula.
A cylinder weighing 445 N and having a diameter of 1 m floats in salt water (sp.gr. 1.03) vertically. It has an anchor tied to the cylinder, where the anchor rest at the bottom of the earth. The anchor weigh 23540 N/m3 and has a volume of 0.280 m3. What height “h” above the water surface will be required to lift the anchor off the bottom of the water when a high tide occur? The part of the cylinder is submerged 0.30 m below the salt water.
A liquid is placed inside a chamber and its pressure is 1,546 MPa and its volume is 1.6 m3. After a while a pressure of 2,019 MPa is applied and its volume decreased to 1.1 m3. Determine the Bulk Modulus in GPa.
The test tube opens at 293 K with 13 cm Hg at the bottom, and 5.6 cm water above Hg. Calculate the pressure at the bottom of the tube if the atmospheric pressure is 760 mm Hg. Use a density of 13.55 g / cm3 for Hg and 0.998 g / cm3 for water. Give answers in terms of dyne / cm2, psia, and kN / m2 • (See conversion table). = kPa. = ..... dyne / cm2. = .... psia = ....
The Bulk Modulus of 1 kg of water is 2.2 GPa. If the percentage reduction in volume is 6%, determine the pressure applied. Express your answer in the appropriate SI unit Round off ONLY the final result to three decimal places as applicable.
The bulk modulus of 1kg of water is 2.2 GPa. If the percentage reduction in volume is 6%, determine the pressure applied. express your answer in appropriate SI unit. thank you
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.
The density of a floating body can be determined by tying weights to the body until both the body and the weights are completely submerged, and then weighing them separately in air. Consider a wood log that weighs 1400 N in air. If it takes 34 kg of lead (? = 11,300 kg/m3) to completely sink the log and the lead in water, determine the average density of the log.
A vertical cylinder gasoline storage tank is 30m in diameter and is filled to a depth of 15m with gasoline of mass density 740 kg/m³. if the shell plating has an allowable stress of 100 MPa, calculate the required wall thickness at the bottom of the tank.
The hollow ball shown in (Figure 1) is made of plastic and filled with air so that its average density is ρb = 48 kg/m^3. Assume r = 0.6 m. Determine the magnitude of the tension in the cable AB if the ball is submerged in the water at the depth shown.The volume of a ball is V=4/3πr^3