A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 5.00 cm2 and a large one of cross-sectional area of 375 cm2. If the lift designed to lift a car with a mass of 2000-kg truck, what minimum force (in newtons) must be applied to the small piston? [g = 9.80 m/s2] Express your answer in units of newtons but do not type units in your answer. For example, if your answer is 300 N, enter 300 as your answer.

A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 5.00 cm2 and a large one of cross-sectional area of 375 cm2. If the lift designed to lift a car with a mass of 2000-kg truck, what minimum force (in newtons) must be applied to the small piston? [g = 9.80 m/s2] Express your answer in units of newtons but do not type units in your answer. For example, if your answer is 300 N, enter 300 as your answer.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 6P: The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its...

See similar textbooks

Similar questions

The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN? Figure P15.6
The small piston of a hydraulic lift (Fig. P14.8) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN?
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
The hydraulic system of a backhoe is used to lift a load as shown in Figure 11.45. (a) Calculate the force F the slave cylinder must exert to support the 400-kg load and the 150-kg brace and shovel. (b) What is the pressure in the hydraulic fluid if the slave cylinder is 2.50 cm in diameter? (c) What force would you have to exert on a lever with a mechanical advantage of 5.00 acting on a master cylinder 0.800 cm in diameter to create this pressure? Figure 11.45 Hydraulic and mechanical lever systems are used in heavy machinery such as this back hoe.
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
Pascal’s Principle and Hydraulics 59. How much pressure is transmitted in the hydraulic system considered in Example 14.3? Express your answer in atmospheres.
Review. The lank in Figure P14.15 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 in that is hinged at the top of the hatch, (a) Determine the magnitude of the force the water exerts on the hatch, (b) Find the magnitude of the torque exerted by the water about the hinges.
Calculate the Reynolds numbers for the flow of water through (a) a nozzle with a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when the nozzle is attached to the hose. The flow rate through hose and nozzle is 0.500 us. Can the flow in either possibly be laminar?
What fraction of ice is submerged when it floats in freshwater, given the density of water 0°C is very close to 1000 kg/m3?
Water is moving at a velocity of 2.00 m/s through a hose with internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
How would you determine the density of an irregularly shaped rock?