A jet is deflected by an angle of 90 degrees, as shown below. Before the impact on the blade (solid- hatched region), the velocity of the jet is 17 m/s and the diameter of the jet is 10 mm. Using Bernoulli and ignoring any friction/losses or gravity effects, calculate the velocity magnitude of the jet after the interaction. Consider that the deflection occurs at atmospheric pressure and the density of the jet is 1021 kg/m3. 90 Uo, Po, Do О а. 34 m/s O b. 0 m/s O c. 8.5 m/s O d. 17 m/s u=?

A jet is deflected by an angle of 90 degrees, as shown below. Before the impact on the blade (solid- hatched region), the velocity of the jet is 17 m/s and the diameter of the jet is 10 mm. Using Bernoulli and ignoring any friction/losses or gravity effects, calculate the velocity magnitude of the jet after the interaction. Consider that the deflection occurs at atmospheric pressure and the density of the jet is 1021 kg/m3. 90 Uo, Po, Do О а. 34 m/s O b. 0 m/s O c. 8.5 m/s O d. 17 m/s u=?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The external and internal diameters of the inward flow reaction turbine 60 cm and 30 cm, the width of the inlet are 15 cm. The flow velocity through the runner is constant throughout and is equal to 1.5 m/s. Calculate discharge and the width at the outlet if 8% of the circumferential area is occupied by the blade thickness at both inlet and exit.
In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
A nozzle inclined at an angle of 68° with the horizontal issues an 82-mm-diameter water jet at a rate of 14 m/s. What is the area (in sq. m.) of the jet at the highest point of the projectile? Neglect air resistance.
Water is passing through a vertical nozzle.The flow rate is 40kg/s and the cross section area at the inlet and outlet is given as 149 and 36cm^2 respectively. The outlet area of the nozzle is open to the atmosphere. Please compute the horizontal component of the anchoring force.
Calculate the flow rate, jet velocity, and the reaction force for each deflection angle. Plot this theoretical reaction forceagainst jet velocity.2. For each deflection angle, plot the actual balancing weight against the theoretical reaction force; does theplot suggest a 45° linear relation?
jet of water of diameter 100 mm strikes a curved plate at its center with a velocity of 15 m/s. The curved plate is moving with a velocity of 7 m/s in the direction of the jet. The jet is deflected through an angle of 150°. Assuming the plate smooth find: (i) Force exerted on the plate in the direction of the jet. (ii) Power of the jet, and (iii) Efficiency.
Q6) A water jet hits horizontally a 50-kg block with a velocity of (20 m/s), see the figure. The friction coefficient between the block and the ground is (0.9). What is the minimum diameter (d) of the water jet required for the block to slide to the left?
6.36 This two-dimensional water (at 50°F) jet is deflected by the two-dimensional vane, which is moving to the right with a speed of 60 ft/s. The initial jet is 0.30 ft thick (vertical dimension), and its speed is 100 ft/s. What power per foot of the jet (normal to the page) is transmitted to the vane? See §6.5 for useful knowledge about moving CVs.
A fire pump delivers water through a 150 mm main to a hydrant to which is connected a 75 mm hose, terminating in a 25 mm nozzle. The nozzle is 3 m above the hydrant and 18 m above the pump. Assuming a total frictional loss of 18.5 m from the pump to the base of the nozzle, and a loss in the nozzle of 10 per cent of the velocity head in the jet, and neglecting air resistance, what gage pressure at the pump is necessary to throw a stream 30 m vertically above the nozzle?
A large lawn sprinkler with two identical arms is used to generate electric power by attaching a generator to its rotating head. Water enters the sprinkler from the base along the axis of rotation at a rate of 5 gal/s and leaves the nozzles in the tangential direction. The sprinkler rotates at a rate of 180 rpm in a horizontal plane. The diameter of each jet is 0.5 in, and the normal distance between the axis of rotation and the center of each nozzle is 2 ft. Determine the maximum possible electrical power produced.
A large lawn sprinkler with two identical arms is used to generate electric power by attaching a generator to its rotating head. Water enters the sprinkler from the base along the axis of rotation at a rate of 5 gal/s and leaves the nozzles in the tangential direction. The sprinkler rotates at a rate of 180 rpm in a horizontal plane. The diameter of each jet is 0.5 in, and the normal distance between the axis of rotation and the center of each nozzle is 2 ft. If the rotating head is somehow stuck, determine the moment acting on the head.
A single-acting reciprocating pump has piston diameter 12 cm and stroke length of 30cm. The center of the pump is 5m above the water level sump. The diameter and length of suction pipe are 7.5cm and 8m respectively. The separation occurs if the absolute pressure head in the cylinder during suction stroke falls below 2.5 m of water. Calculate the maximum speed at which the pump can run without separation. Take atmospheric pressure head = 10.3 m of water.