A jet of velocity of 20 m/s strikes a flat plate inclined at 30° with the axis of the jet. If the cross sectional area of the jet is 20 cm2, find the force exerted by the jet on the plate. Also calculate the components of the force in the direction normal to the jet. Find also the ratio in which the discharge gets divided after striking the plate.

A jet of velocity of 20 m/s strikes a flat plate inclined at 30° with the axis of the jet. If the cross sectional area of the jet is 20 cm2, find the force exerted by the jet on the plate. Also calculate the components of the force in the direction normal to the jet. Find also the ratio in which the discharge gets divided after striking the plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water jet in figure, moving at 15 m/s, is split so that one-third of the water moves towardA. Calculate the magnitude and direction of the force on the stationary splitter.
A horizontal water jet of constant velocity V impinges normally on a vertical flat plate and splashes off the sides in the vertical plane. The plate is moving toward the oncoming water jet with velocity 1/2V. If a force F is required to maintain the plate stationary, how much force is required to move the plate toward the water jet?
A cylindrical tank discharges water at 20^O C through a well-rounded orifice to hit an inclined plate as shown in the figure. Determine the components of the force exerted by the fluid jet on the plate inclined at 60^O from the horizontal.( Assume the external and internal pressures are the same)
Once it has been started by sufficient suction, the siphon in the Fig. will run continuously as long as reservoir fluid available. Using Bernoulli's equation with no losses, show (a) that the exit velocity V2 depends only on gravity and the distance H and (b) that the lowest vacuum pressure occurs at point 3 and depends on the distance L+H
In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
A 3"-diameter jet has a velocity of 110 fps. It strikes a blade moving in the same direction at 70 fps. The deflection angle is 150°. Assuming no friction, determine the final absolute velocity of the water V2 as it leaves the blade.
A jet of water of diameter 75 mm moving with a velocity of 25 m/s strikes a fixed plate in such a way that the angle between the jet and plate is 60°. Determine the force exerted by the jet on the plate (i) in the direction normal to the plate and (ii) in the direction of the jet.
A large tank with a nozzle attached contains three immiscible, inviscid fluids as shown. Assuming that the changes in h1, h2 and h3 are negligible, find the expression of instantaneous discharge velocity?
Find the force exerted by a jet of water of diameter 75 mm on a stationary flat plate, when the jet strikes the plate normally with velocity of 20 m/s.
A jet of water strikes a stationary curved vane and is deflected by 150° from its originaldirection. The mass flow rate from the jet is 0.68 kg/s and has a velocity of 24 m/s. Calculatethe magnitude and direction of the resultant force on the vane.
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the sprinkler nozzles as 2cm diameter jets at an angle of u from the tangential direction. The length of each sprinkler arm is 0.52 m. Disregarding any frictional effects, determine (a) Angular momentum and (b) the rate of rotation n of the sprinkler in rev/min For ϴ = 30°
A circular deep dish has a sharp-edged hole in its center. A jet of water speed V, hit the plate concentrically. Get an expression for external strength necessary to hold the dish in place, if the jet emitted from the hole also has speed V. Evaluate the force for V=5 m/s, D= 100 mm and d = 20 mm.