A lap welded joint of A36 steel plates must hold a tensile load. The lower plate is .5 inches thick and 7.7 inches wide. The upper plate is .5 inches thick and 4.8 inches wide. Use Class E60 series electrodes with 1/4 inch leg welds. Using side fillet welds only, A. find the maximum allowable tensile load the joint can support and determine the required overlap between the plates to achieve this strength B. what is the required overlap to meet the maximum tensile load

A lap welded joint of A36 steel plates must hold a tensile load. The lower plate is .5 inches thick and 7.7 inches wide. The upper plate is .5 inches thick and 4.8 inches wide. Use Class E60 series electrodes with 1/4 inch leg welds. Using side fillet welds only, A. find the maximum allowable tensile load the joint can support and determine the required overlap between the plates to achieve this strength B. what is the required overlap to meet the maximum tensile load

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.13P

See similar textbooks

Similar questions

Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A flat bar used as a tension member is connected to a gusset plate. Size of weld is 6 mm, with an ultimate tensile strength of 185 MPa. E 70 electrodes Thickness of plate = 6.25 mm. Use ASD. Thickness of gusset plate = 9.5 mm. Fy = 248 MPa Fw = 0.60(485) Fu = 400 MPa Questions: The connected parts are of A-36 steel and assumed that the tensile strength of the member is adequate: a) Determine the strength of the connection per mm considering the design shear strength of the 6 mm fillet weld. b) Determine the base metal shear strength per mm. c) Determine the available strength of the connection.
Question 6 Two plates of Steel A72 Gr 50 are connected with each as shown in Figure 5. E70XX Electrodes were used and 7/16 in fillet weld were made by SMAW process. What is the design strength of the weld by LRFD and ASD? E10 in - 10in P, or P. - PLx 10 Figure # 4
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu=483.33 MPa. Fv = 0.30 Fu Questions: a) Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. b) Determine the length of side fillet weld required at the heel. c) Determine the length of side fillet weld required at the toe.
A steel side plate is welded to a vertical steel column according to the specifications in Fig. 1. An E 70 welding electrode is used, and there is an applied load of F = 20 kN. %3D What weld size, s, is needed for a safety factor of 2 guarding against yield? F B, 150 C 100' - 200 Dimensions in millimeters Figure 1: Side plate welded to a vertical steel column.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.
Determine the total LFRD design strength and the total ASD allowable strength of the 5/16 – in E70 fillet welds shown.
Two steel plates are lap jointed in a workshop using 6 mm thick fillet weld as shown in the figure (not drawn to the scale). The ultimate strength of the weld is 410 MPa. 120 mm Fillet weld 200 mm As per Limit State Design is IS 800 : 2007, the design capacity (in kN, round off to three decimal places) of the welded connection, is
The connection shows a PL10X200 loaded in tension and welded to a gusset plate 10mm thick. Calculate the following, assuming A992 steel is used. Use U =0.85. The weld thickness is ómm and the electrode is E70 (485MPA). PL 10 X 200 350mm What is the allowable weld connection strength (kN)?
Q3. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet weld. If a torque is applied to the shaft, calculate the size of the weld joint.
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.