b) For the welded connection below, fillet weld of different lengths are provided at the heel and the toe of the angle. Matching strength electrode E49XX is used. Comment whether the welding provided meets the minimum weld size and length requirement. If it does not, state what need to be changed. according to the welding provided. Regardless, calculate the resistance 80 B 2L76x76x11 T B PL 25 B-B

b) For the welded connection below, fillet weld of different lengths are provided at the heel and the toe of the angle. Matching strength electrode E49XX is used. Comment whether the welding provided meets the minimum weld size and length requirement. If it does not, state what need to be changed. according to the welding provided. Regardless, calculate the resistance 80 B 2L76x76x11 T B PL 25 B-B

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.5.4P

See similar textbooks

Similar questions

In the below welded connęction, the %-inch fillet weld of E70 electrode is along the entire width of the A36 steel plates.. -10-in. x-in. plate- 10-in. x2-in. plate- a) Determine the shear strength of the weld a) Determine the tensile strength of the plates b) What is the strength of the welded connection?
Question 6 Two plates of Steel A72 Gr 50 are connected with each as shown in Figure 5. E70XX Electrodes were used and 7/16 in fillet weld were made by SMAW process. What is the design strength of the weld by LRFD and ASD? E10 in - 10in P, or P. - PLx 10 Figure # 4
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A flat bar used as a tension member is connected to a gusset plate. Size of weld is 6 mm, with an ultimate tensile strength of 185 MPa. E 70 electrodes Thickness of plate = 6.25 mm. Use ASD. Thickness of gusset plate = 9.5 mm. Fy = 248 MPa Fw = 0.60(485) Fu = 400 MPa Questions: The connected parts are of A-36 steel and assumed that the tensile strength of the member is adequate: a) Determine the strength of the connection per mm considering the design shear strength of the 6 mm fillet weld. b) Determine the base metal shear strength per mm. c) Determine the available strength of the connection.
A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back of the channel. All steel is A36 with Fy=250 MPa and Fu=400 MPa. Use E70electrodes having and Fu=485 MPa (SMAW) process. The maximum length of lap is 250mm. The size of fillet weld is 8mm. Assume the width of slot weld is 22 mm. Size of slot weld is 13mm Properties of C250x37 A = 4750 mm2 tw = 13.0 mm2 d = 254 mm a. Determine the force resisted by the slot weld in kN, when the full tensile capacity is 712.5 KN (from the gross yielding capacity using ASD) Hint: Full tensile Capacity = Force Resisted by Fillet and Slot Weld Round your answer to 3 decimal places.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The angle 150x100x10mm is connected to a 8.5 mm gusset plate. The size of weld is 8 mm and using E70 Electrodes. Fu = 438 MPa. Use LRFD. Questions: a) Find the length of the weld required at the toe of the angle. b) Find the length of the weld required at the heel of the angle. c) Find the block shear strength of the gusset plate.
A steel side plate is welded to a vertical steel column according to the specifications in Fig. 1. An E 70 welding electrode is used, and there is an applied load of F = 20 kN. %3D What weld size, s, is needed for a safety factor of 2 guarding against yield? F B, 150 C 100' - 200 Dimensions in millimeters Figure 1: Side plate welded to a vertical steel column.
Determine the total LFRD design strength and the total ASD allowable strength of the 5/16 – in E70 fillet welds shown.
The connection is shown in Fig. 3. Two cover plates are applied to connect the steel plates by fillet welds. The dimensions of connection are presented in Fig. 3. The leg size of fillet weld hr is 10 mm. Q235 steel, f-215 N/mm2, E43 electrode, fav=160N/mm?. Calculate the load-carrying capacity of the fillet weld connection wwww. (Note: the strength of steel plate should be calcualted. (Unit: mm) 220 ス20 091
A lap welded joint of A36 steel plates must hold a tensile load. The lower plate is .5 inches thick and 7.7 inches wide. The upper plate is .5 inches thick and 4.8 inches wide. Use Class E60 series electrodes with 1/4 inch leg welds. Using side fillet welds only, A. find the maximum allowable tensile load the joint can support and determine the required overlap between the plates to achieve this strength B. what is the required overlap to meet the maximum tensile load
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.
Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles will be made from A36 steel, and the gusset plate from A572 Gr. 50 steel. Use 70ksi electrode. Design the system to resist a factored load of 200 kips. Check all applicable limit states that are possible. Provide your results on a sketch with standard weld symbols and details.
Q- A fillet weld of size 6mm used to weld a plate of width 75mm to gusset plate to transfer a factored load of 120kN, assuming site weld and Fe410 steel, the length of each side of fillet weld (in mm) is (Assume that the welding is done along the width also on one side).