Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds for the full capacity the 125x100x10mm angle tension member as shown below. Assume that the member is subjected to repeated stress variations making any connection eccentricity undesirable. Check the block shear strength of the member. Assume that the WT chord has sufficient strength to develop the weld strengths and the thickness of its web is 12mm. Use U=0.87 for class use and LRFD Method only.

Using SMAW process, E70 electrodes and an A572 steel. Determine the length of the side fillet welds for the full capacity the 125x100x10mm angle tension member as shown below. Assume that the member is subjected to repeated stress variations making any connection eccentricity undesirable. Check the block shear strength of the member. Assume that the WT chord has sufficient strength to develop the weld strengths and the thickness of its web is 12mm. Use U=0.87 for class use and LRFD Method only.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.15P

See similar textbooks

Similar questions

Using SMAW process, E70 electrodes and an A572 steel. Determine thelength of the side fillet welds for the full capacity the 125x100x10mm angle tensionmember as shown below. Assume that the member is subjected to repeatedstress variations making any connection eccentricity undesirable. Check theblock shear strength of the member. Assume that the WT chord has sufficientstrength to develop the weld strengths and the thickness of its web is 12mm. UseU = 0.87 for class use and LRFD Method only.
Find the Load Capacity of the weld if the throat thickness is 8. 13 mm, Nominal Tensile Strength, Fu = 520 MPa, and length of weld = 400 mm.
5. Determine the size of the fillet weld required for the shear and tension connection if p = 200KN, 5 = 150mm, b = 150mm and d = 20mm. Use E70 electrodes and assume the column and bracket plate does not control the strength. Steel Column Bracket (out from resection UNMA COC
One leg of an 8 x 8 x 3/4 angle is to be connected with side welds and a weld at the end of the angle to a plate behind, to develop the loads PD = 170 k and PL = 200 k. Balance the fillet welds around the center of gravity of the angle. Using LRFD and ASD methods, determine weld lengths if E70 electrodes and maximum weld size is used.
Q: Design Fillet welded connection using E65X electrodes to connect three plate sections (W=20in & t=0.75”) for transmitting dead load of 10k & live load of 140k.Consider minimum weld thickness (S=5/8”) with “A36” member steel (fy=36 ksi & fu=58 ksi).
Q#1: Design Fillet welded connection using E65X electrodes to connect three plate sections (W=20in & t=0.75”) for transmitting dead load of 10k & live load of 140k.Consider minimum weld thickness (S=5/8”) with “A36” member steel (fy=36 ksi & fu=58 ksi).
Determine the rupture failure load of the given tension member. Use the NSCP 2015. Problem: A tension member L152×102×12.7 is connected to the gusset PL16mm with 130mm welds.
A 4 x 4 x ½ - in. angle of A36 steel is to be welded to a plate with E70XX electrodes to develop the full tensile strength of the angle. Using 3/8-in. fillet welds, compute the design lengths for the welds on the two sides of angle, assuming development of tension on the full cross section of the angles. GIVEN: A = 3.75 in2 L1 = 10.94” L2 = 5.09” IF only connected leg, L = 7.7”; 4.75 each side
A WT6x15 shape made from A36 steel will be welded along its flanges to a gusset plate. Determine the LRFD available strength, φRn, for gross tension yield of the WT shape. Determine the required weld length, l, on each side of the WT in order to exceed the LRFD available strength for gross tension yield of the WT shape. Assume a weld size of w=5/16 inch and E70XX electrodes. Based on the weld length, compute the available LRFD strength, φRn, for tensile rupture of the WT shape.
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.
Design a welded connection (E70) for an MC 9x23.9 of A992 Grade 50 steel connected to a 3/8-inch-thick gusset plate. The gusset plate is A36 steel. Minimize the length of the longitudinal welds by using the maximum fillet weld size permitted (AISC J-2b). Show your results on a sketch, complete with dimensions. Use LRFD. Hint: Design it with both longitudinal welds and a transverse weld. For simplicity in the iteration of this problem take U = 1.0 and thus no shear lag effects. Also, do not forget to consider the block shear that will occur in the gusset plate.
a. Determine the design strength of a 1-in length of a 1/4-in fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength FEXX = 70 ksi. Assume that load is to be applied parallel to the weld length.b. Repeat part (a) if the weld is 20 in long.c. Repeat part (a) if the weld is 30 in long.