A lever is used to lift a boulder. The fulcrum is placed 1.95 m away from the end at which you exert a downward force, producing a torque with a magnitude of 500 N•m. If the angle between the force and the lever is 80.0°, what is the magnitude of the applied force?

A lever is used to lift a boulder. The fulcrum is placed 1.95 m away from the end at which you exert a downward force, producing a torque with a magnitude of 500 N•m. If the angle between the force and the lever is 80.0°, what is the magnitude of the applied force?

Name: What is the magnitude of the applied force? A lever is used to lift a
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: What is the magnitude of the applied force? A lever is used to lift a boulder. The fulcrum is placed 1.95 m away from theend at which you exert a downward force, producing a torque with amagnitude of 500 N•m. If the angle between the force and the le

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 82P: What force must be applied to end of a rod along the x-axis of length 2.0 m in order to produce a...

See similar textbooks

Similar questions

What is the torque abot the origin of the force if it is applied at the point whose position is:
A hollow cylinder that is rolling without slipping is given a velocity of 5.0 m/s and rolls up an incline to a vertical height of 1.0 m. If a hollow sphere of the same mass and radius is given the same initial velocity how high vertically does it roll up the incline?
When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?
A pendulum consists of a rod of length 2 m and mass 3 kg with a solid sphere of mass 1 kg and radius 0.3 m attached at one end. The axis of rotation is as shown below. What is the angular velocity of the pendulum at its lowest point if it is released from rest at an angle of 30 ?
A 40.0-kg solid cylinder is rolling across a horizontal surface at a speed of 6.0 m/s. How much work is required to stop it?
A solid cylinder of radius 10.0 cm rolls down an incline with slipping. The angle of the incline is 30 . The coefficient of kinetic friction on the surface is 0.400. What is the angular acceleration of the solid cylinder? What is the linear acceleration?
The precession angular velocity of a gyroscope is 1.0 rad/s. If the mass of the rotating disk is 0.4 kg and its radius is 30 cm, as well as the distance from the center of mass to the pivot, what is the rotation rate in rev/s of the disk?
A cylinder with rotational inertia I1=2.0kgm2 rotates clockwise about a vertical axis through its center with angular speed 1=5.0rad/s . A second cylinder with rotational inertia I2=1.0kgm2 rotates counterclockwise about the same axis with angular speed 2=8.0rad/s . If the cylinders couple so they have the same rotational axis what is the angular speed of the combination? What percentage of the original kinetic energy is lost to friction?
What force must be applied to end of a rod along the x-axis of length 2.0 m in order to produce a torque on the rod about the origin of 8.0k Nm ?
A solid cylinder rolls up an incline at an angle of 20 . If it starts at the bottom with a speed of 10 m/s how far up the incline does it travel?
A diver goes into a somersault during a dive by tucking her limbs. If her rotational kindetic energy is 100 J and her moment of inertia in the tuck is 9.0kgm2 , what is her rotational rate during the somersault?
Find the torque about the origin produced by a constant force of (6i+8j+10k)N on a praticle situated at (3i+4k)m