Answered: A lighting load operates from a 208V,…

A lighting load operates from a 208V, 60Hz supply and is rated 1 kW @ p.f. .707 lagging. What size capacitor must be connected to raise the power factor to 0.91 lagging? Gien

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2MCQ: If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by...

See similar textbooks

Related questions

Q: An alternator is supplying a load of 300 kW at a p.f. of 0.6 lagging. If the p.f. is raised to…

A: Given, An alternator is supplying a load of, P1 = 300 kW At power factor, cosϕ1=0.6 lagging Raised…

Q: ww Consider the following circuit diagram. 20 Q 2 mF wwH 50230 V @ = 2000 rad/sec 4 mH R, Find the…

A: The given circuit is: The maximum power across RL can be calculated with the help of maximum power…

Q: A resistor of 4 ohmsisconnected in parallel with an impedancecoil whose resistance and inductive…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: A 50HZ, two wire transmission line delivers a load with 2500KW,35KV at 0.85 power factor lagging.…

A: Need to find type of load

Q: For the circuit with source V1 shown below, determine the average power supplied by V1: v1(t) = 15…

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: In this question, We need to determine the power supplied by the power company? If power factor…

Q: The voltage applied to a coil having R-2002 ohm, L-638 mH is represented by e=20sin 100 pi t. Find a…

Q: Compute the rms value of the voltage waveform shown in Fig. v(t) (V) 4 ил. 2 4 6 8 t(s)

A: By using the concept of signal and systems we need to calculate the value of RMS voltage of the…

Q: An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is…

A: Given, Active power, P = 300 kW Power factor, cosϕ=0.6 lagging When the power factor is raised to…

Q: Q/ when connected to a 120V (rms), 60HZ power line , a load absorbs 4Kw at a lagging power factor of…

Q: DETERMINE THE AVERAGE LOAD VOLTAGE IN THE POWER DELIVERED TO THE LOAD IF C=4チィィF 10:1 220 Vac…

Q: Find the resultant of the two out of phase current If the component currents are 12 and 16 amp.,…

Q: An equipment that draws 9.4 kW at 0.83 power factor lag. How much reactive power in kVAr is…

A: Reactive power = active power ×tan(power factor angle). Power factor angle = arc cos(power factor).…

Q: The AC EMF in this electric circuit is described by the following equation: E = 30VE(20 rad )t What…

Q: The average Powet to the Plant Shown in Fig is 2479 KW and Powey factor is 0.707 with W=377 tad/sec…

A: Given Real power of plant(Pp)=2479 KWPower factor of plant(cos∅1)=0.707 lagω=377 radsecEffective…

Q: Example XL Determine the power factor and the true ll power (average power) in the shown circuit :…

A: given here a circuit and asked to calculate the power factor and average power. and given voltage is…

Q: An engine consumes 50 kW at a power factor 0.8 lagring.from a 220 Vrms and 100Hz line, find…

Q: n alternator is supplying a load of 350 kW at a p.f of 0.7 lagging. If the power factor is raised to…

A: The solution is attached below for the given alternator problem.

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: Power factor is defined as the ratio of active power to apparent power. It gives an idea about how…

Q: The 2430 KW average power the plant sShown in fig to and the Power factor is o lo1 logging. The…

Q: The photo below has the question. Thanks!!

A: For 200 hp motor loaded to 100 hp (pf =0.6 lag)-

Q: For the circuit shown in Fig. find the power supplied by 12 Kv Fig 12kV rms ( 400 kw 0.707 PF lag

A: Given, cosϕ=0.707P=400 KW

Q: Q10. If the impedance of a circuit = 20 – j10 1. if a voltage source is connected across this…

A: Given: Impedance Z=20-j10Ω Voltage source is connected across impedance.

Q: Find the average power absorbed by a circuit component that has a voltage of v = 20.3…

Q: Q2 (a) In each case below, sketch two AC signals, V(t) and Vs(t), which have the same frequency,…

Q: Given the network in the figure below, determine the magnitude of the input voltage Vs. 0.3 0 jo.1 N…

A: Given network,

Q: Find the power supplied by the power company. Determine how it changes if the power factor is…

A: This question belongs to circuit theory . It is based on the concept of power factor in the circuit…

Q: A generator is supplying a load of 500 kW at a power factor of 0.8 lagging. If the power factor is…

Q: The avg power to the plant Shown in fig in 2430 KW o 107 lagging. The and the power factor genorador…

Q: A medium-rise building with inductive loads has an average consumption of 40 kW and 26 KVAR. At the…

A: In this question we need to find a minimum KVAR the capacitor should produce so that the surcharge…

Q: A phasor voltage V = 100/45° V (the sinusoid operates at 155 rad/s) is applied to the parallel…

Q: A medium-rise building with inductive loads has an average consumption of 40 kW and 26 KVAR. At the…

A: As per the guidelines of Bartley we supposed to answer first three subpart only for solution of…

Q: A building with inductive loads has an average consumption of 40kW and 26 kVAR. What is the average…

Q: For the circuit shown in Fig. , find the power supplied by 12 Kv Fig 12kV rms ( 400 kw 0.707 PF lag

A: Let the voltage across the 400 kW load be V2. P=V2×I×Cosϕ400 kW=V2×I×0.707V2×I=4000002V2=4000002I

Q: Determine the average load voltage in the circuit and the power delivered to the load if C= 47µF

Q: A generator is supplying a load of 700 kW at a power factor of 0.9 lagging. If the power factor is…

A: We have been given a generator which is supplying a load of 700 KW with, Cosϕ = 0.9 Lagging and we…

Q: Determine the VAR rating of the power factor correction capacitor required to improve the power…

Q: An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is…

A: Given, Active power rating, P1 = 300 kW Power factor, cosϕ1 = 0.6 lagging At power factor, cosϕ2=1…

Q: A synchronous motor absorbing 60 kW is connected in parallel with a factory load of 240 kW having a…

A: The synchronous motor is connected in parallel with a factory load hence total active power of the…

Q: The voltage applied to a coil having R-2002 ohm, L-638 mH is represented by e=20 sin 100 ? t. Find a…

Q: Calculate the power factor of the er source. What is the average power supplied by the 102 4020°…

Q: Determine the complex power for the following give values and specify whether the power factor is…

Q: For the circuit with source V1 shown below, determine the average power supplied by V1 v1(t) = 15…

A: Circuit is given as,

Q: In the circuit in Fig, the 60-W resistor absorbs an average power of 240 W. Find V and the apparent…

A: Introduction: When there are resistance, capacitance and inductance in the circuit. Total resistance…

Q: Exercise Problem 8.22 Determine ix(t) and average power delivered by the source.

A: N1N2=14i1N1=i2N2N1N2.i1=i2i2=N1N2 i1i2=14 i1jωL1=j13=j3Apply KVL--7∠0°+i14+i3j3+5i3=0…

Q: A medium-rise building with inductive loads has an average consumption of 40 kW and 26 KVAR. At the…

Q: The line voltage on a 146 kW 0.7 PF lagging load is 480 Vrms. Find the value of the capacitance that…

Q: An ac load has the following electrical specifications P = 61 kW V = 630 V rms pf = 0.8 lagging…

Question

A lighting load operates from a 208V, 60Hz supply and is rated 1 kW @ p.f. .707 lagging. What size
capacitor must be connected to raise the power factor to 0.91 lagging?
Gien

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

An industrial load connected to a 440 V, 60 Hz line takes 50 A. The current lags the voltage by 30 electrical degrees. What is the power factor of this circuit? Determine the apparent power, in volt-amperes and the true power, in watts
A building inventory identified the following equipment with the corresponding impedance or power consumption at 230 V rms. The building power supply is 230 V rms. (Assume that the building voltage supply is the reference phasor) What is the total complex power consumed within the building and the effective power factor? Load 1: 160 - j40  Load 2: 500 VA at 0.85 pf lag Load 3: 450 W at 0.95 pf lead Load 4: 200 + j300 VA
NEED ASAP please solve this problem,Maximum Average Power Transfer. Please show full and complete solution Note: Answer from the book for Pmax is lower than 50W
Given voltage source = 100V∠0°, give the value of real power, apparent power, and reactive power consumed by the network. Give also the power factor of the network.
The power company supplies 80 kW to an industrial load. The load draws 220 A rms from the transmission line. If the load voltage is 440 V rms and the load power factor is 0.8 lagging, what is the value of the lost power in the transmission line?
A generation station of 1MW supplied a region which has the following demands:
Compute the average power dissipated by the load seen by the voltage source in the given figure. Let ω = 377 rad/s, Vs = 50 ∠0° V, R = 19.5 ohm, L = 0.08 H, and C = 200 μF.
The power company supplies 80 kW to an industrial load. The load draws 220 A rms from the transmission line. If the load voltage is 440 V rms and the load power factor is 0.8 lagging, what is the value of the lost power in the transmission line? (Write the value)
Find the average power delivered by the ideal current source in the circuit if ig=40cos 1250t mA.
An engine consumes 50 kW at a power factor 0.8 lagring.from a 220 Vrms and 100Hz line, find capacitors in parallel with the load which makes the power factor 1
A single-phase consumer who lives in San Francisco has an annual average monthly consumption of 430 kWh. In San Francisco, the average hours of full sun is 3.96 hours / day. Considering the losses of 20%, based on the data below (image), find: The number of photovoltaic panels that will be used.
An industrial load with a power factor of 0.707 lagging. If the voltage across the load is 98<0. Find the angle of the current supplied to the load.