Answered: An ac load has the following electrical…

An ac load has the following electrical specifications P = 61 kW V = 630 V rms pf = 0.8 lagging Detemine the magnitude of the load current in Amper correct to nearest 1 decimal place.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24P: A source supplies power to the following three loads connected in parallel: (1) a lighting load...

See similar textbooks

Related questions

Q: The switch in the circuit shown in Figure Q1(c) has been in position a for a long time. At t-0, the…

A: In this question we need to find a voltage VC(t) , Vo(t) and io(t)

Q: System Determine the solution of the following differential equations using Laplace Transform y" -…

Q: Find the z-transform of an–1.

A: In this question, We need to Find the z-transform of an-1

Q: The analysis of the voltage, V for the cireuit given in Figure Q4 can be expressed in the following…

A: Id =0.5882 V3 =200×0.5882=117.64 V

Q: Vo(s) V(s) each of the operational amplifiers shown, find the transfer function G(s) %3D 100k ohms…

Q: The discrete time Fourier series representation of a signal x[n] with period N is written as x[n] =…

A: By using Discrete Time Fourier Series expression

Q: A designer will be using a silicon diode over a temperature range of 0 to 75 degree Celsius. What is…

Q: A balance Y-connected load of ( 3 + j8 ) ohms per phase is supplied by a balanced three- phase, 60…

A: In this question, We need to determine the value of line current, real power and imaginary power…

Q: (B)- Indicate whether the following statements are true or false and correct the fals statementS. こに…

A: In this question we will write about dc motor related questions and about interpole winding....…

Q: The conduction angle of SCR in AC chopper fed R-load is equal to

Q: Suppose that R1 14 2, R2 =9 N. Part A Figure < 1 of 1 Determine the value of I, in the circuit shown…

A: Given data, R1=14 ΩR2=9 Ω

Q: 200-kVA transformer has an iron loss of 1 kW and full load copper loss of 2 kW. Its load kVA…

A: The solution is given below

Q: What is the required value of ? for a voltage gain of 10 b) Determine ?out

Q: Calculate the radiation efficiency, in %, for a half wavelength dipole antenna whose radiation…

Q: Implement the below logic function with an 8 :/ multiplexer. AzA2 A,Ã¸+ A3A, +A,A,A,A, + A, A,4,A,t…

A: A logic expression is given in the question. We need to implement the logic expression by a 8:1…

Q: Determine the Nyquist rate of a signal whose frequency spectrum is given by ¤(f) = r(f) – 2r(f –…

A: According to bartleby guidelines, we have to answer first question only.

Q: ind the current-voltage relationship of the assumed circuit shown assuming both diodes are Germanium…

Q: The initial values of i and iz in the circuit shown in Figure Q1(b) are +3A and -5A respectively.…

A: For solving this problem one should know about formula of current through inductor

Q: the ripple current is equal to

Q: The analysis of the voltage, V for the circuit given in The below circuit can be expressed in the…

A: Note: value of id is not given. We assume id =0.5882

Q: 4-pole 3-phase IM manufactured by Engr. KC Trinidad which is rated at 60 Hp runs at a supply…

A: We need to find out torque for given motor

Q: The causation of the a in the waveform of the full controlled full wave rectifier is OThe resistive…

Q: Q. Use Table below to explain why the circuit of Figure below will not work as it is. How can the…

A: Integrated circuit are known as microelectronic circuit . This integrated circuit are used in…

Q: How much is 1 line of flux in Webers?

Q: A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158…

Q: A signal A contains 1 period of an infinite periodic signal X, while a signal B contains 4 periods…

A: The Discrete Fourier Transform is a mathematical representation of a signal to study the following…

Q: Find the Thevenin equivalent at terminals a-b of the circuit shown below. What is the value of the…

A: In this question, We need to determine the Thevenin equivalent across the terminal a and b. Find…

Q: 28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1K ohms,…

A: Consider the diodes are practical and have the threshold voltage of 0.7 V. Consider the bridge…

Q: 05- An earth station is receiving a signal from a space research satellite on a frequency of 11GHZ.…

A: We need to find out average power density and received power and effective area of antenna

Q: JR (Jalbuena-Rojas) Industrial and Manufacturing Corporation is rated 4,000 kVA at a power factor of…

A: The solution is given below

Q: EXAMPLE 1 Determine the magnitude of gm for a JFET with Ipss 8 mA and Vp = -4 Vat the following de…

A: In this question we will find transconductance of given JFET....

Q: 100 hp, 440 volts three-phase, 60 hz induction motor operates with 92% efficiency, 0.85 power factor…

A: In this question we will find motor current , synchronous motor starting etc....

Q: Calculate the gate to source voltage VGs for a NMOS transistor with B 2200 HA/V, V=1 V and operating…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: What is the total three-phase real power drawn by the two loads? Express your answer in Megawatts

A: In this question, We need to calculate the total real power of the three phase?

Q: The switch in the circuit shown in Figure Q1(c) has been in position a for a long time. At t-0, the…

Q: Find the z-transform of an cos

A: In this question we will find z transform of given function x(n).

Q: resistor R and an impedance coil Z are connected in series. The combination is supplied by a…

Q: Show that the effective value cr (r.n.s) Sine wave Current w.th peak current Im in Im 2 d

Q: Find the value of ZL for maximum power transfer in the network and th maximum power that can be…

A: In this question, We need to find the value of ZL for the maximum power transfer to the load.…

Q: 6. The used in computers (positive numbers in true form; negative numbers in complement form). (a)…

Q: Complete the table. Solve the currents of the circuit using mesh analysis.Note: If there are no…

A: In this question, We need to determine the loop currents as shown the circuit

Q: Si +32V 4.7k Vo + V - V2 8k2 6 - 8V O 16.72 V O 12.16 V O 6.64 V 31.28 V

Q: The output of a filter is given by Y(t) = X(t) + X(t – T) where X (t) is a WSS process with power…

Q: 10 Q j10 O j10 O ll ll 10 V [1] j5 V sine -j10 Q [12] sine

Q: six pole three-phase 440-volts 50Hz, induction motor develops an 8-Hp at 955 rpm, the power factor…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: alternator is rated at 15kVA, 460V. The armature resistance and reactance are 1.50 and 30…

A: In this question we will find single phase alternator no load voltage with given data...

Q: Find tu oser ad sinusoidal for m of the expressión V 4) = 10 sin (300ot +100) - 5 sin (300ot -75) +…

Q: (B)- Indicate whether the following statemenits are true or false and correct the false statements…

A: Transformer is a static device which is used to step up/down the voltage and current level in the…

Q: 39 ' Si 10 V 10Ω Si Figure 4 Determine the current I using the approximate/practical equivalent…

Q: Q4) Explain briefly the principle of critical angle required for total internal reflection.

Question

An ac load has the following electrical specifications
P = 61 kW
V = 630 V rms
pf = 0.8 lagging
Detemine the magnitude of the load current in Amper correct to nearest 1 decimal place.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Alternating Current (AC) Series Motor and Universal Motor

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
A 240-V rms 60-Hz supply serves a load that is 10 kW (resistive), 15 kVAR (capacitive), and 22 kVAR (inductive). What is the current drawn from the supply in amperes? And what is the required capacitor rating in microfarads required to improve the power factor to 0.96 ?
When connected to a 120 V (rms). 60 Hz power line, a load absorbs 4 kW at a lagging power factor of 0.8. Find the value of capacitance necessary to raise the power factor to 0.95
An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is raised to unity, how many more kW can alternate supply ?
Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the current in B lags behind A by π/3 radians and the total line current is 23.4 amp. (rms), determine the current in B.
Assume you are working on sinusoidal ac supply voltage which is in the form of 150 sin 220 t. So apply this voltage find out following parameters. Analyze the average value of voltage. Options: A)89.85volt B)90.75volt C)86.45volt D)95.55volt
Assume you are working on sinusoidal ac supply voltage which is in the form of 150 sin 220 t. So apply this voltage find out following parameters. Analyze the rms value of voltage. Options. A) 106.05 volt B) 150 volt C) 135 volt D) 130.5 volt
In a chopper circuit the supply power of 2834 W and efficiency is 43 %. Calculate the load power obtained in the circuit a. 1219 W b. 12186 W c. 2834 W d. 2838 W
A 240 VAC RMS 60 Hz source supplies the system. Load 1 is 1000 watts of resistive heating elements. Load 2 is a 3 HP motor with an efficiency of 92% and a lagging power factor of 0.75. Load 3 is a capacitor bank equivalent to 75 microFarads. Draw the system power triangle and determine whether or not load 3 is appropriate to bring the system power factor to unity.Please show the full steps with explanations.
A transformer connected to a120 V (rms) ac line is to supply 12.0 V (rms) to a portable electronic device.The load resistance in the secondary is 5.00 Ω. What rms current must the secondary supply?
500 KVA star connected 440 V alternator supplies full load power to the load at 0.8 lagging power factor. So find the full load current.