(a)(b)200 mm(c)A600 mmB200 mmсFig. 3Fig. 3 shows the layout of a shaft that rotates 500 rev/min and is supported by bearings at O and C. Theshaft is carrying two gears at point A and B, in which the pitch diameter of Gears A and B are 500 mmand 250 mm, respectively. The force, PA applied at Gear A is 3.5 kN. The rotating shaft is made fromAISI 1030 steel, and the factor of safety is 3.PBPA= 3.5 kNList down 2 assumptions needed in designing the shaft in Fig. 3.Design the minimum allowable diameter for the shaft at its critical location.The bearings at points O and C are required to have a desired life of 25kh at a speed of500 rev/min. Based on these conditions, select the appropriate bearings for this

DefinitionBending Moment:If an object undergoes a bend about its certain axis due to some tendency…

(a) List down 2 assumptions needed in designing the shaft in Fig. 3. Design the minimum allowable diameter for the shaft at its critical location. (b) (c) The bearings at points O and C are required to have a desired life of 25kh at a speed of 500 rev/min. Based on these conditions, select the appropriate bearings for this

(a) List down 2 assumptions needed in designing the shaft in Fig. 3. Design the minimum allowable diameter for the shaft at its critical location. (b) (c) The bearings at points O and C are required to have a desired life of 25kh at a speed of 500 rev/min. Based on these conditions, select the appropriate bearings for this

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

power (N)=9.9kw Input speed (n1)=2350rpm Distance between centers (a)=168mm Total distance between Ave B bearings=440mm module(m)=3mm question 3 Calculate the power on the output shaft since there is 3% loss in gears in gearboxes, rolling bearings in support bearings (2% loss in a pair of bearings) and sealing element spring seal (4% loss in a pair of sealing elements).
Q3/ A vertical double acting steam engine develops 80 kW at 240 rpm. The maximum fluctuation of energy is 25% of the work done per stroke. The maximum and minimum speeds are not to vary more than +1% of the mean speed. Find the mass of the flywheel, if the radius of gyration is 0.65 m.
Consider a double hook, thaving intermediate shaft of moment of inertia 3 g-m², the input and output shaft of which are in clined at 30° to intermediate shaft. The input shaft rotates uniformly at 2400 rpm with steady torque of 300 N.m., determine max. fluctuation in output torque.
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20° Assuming that only one pair of the teeth is in contact the total force (in Newton) exerted by a tooth of the pinion on the tooth on a mating gear is...
As seen in the figure, a construction machine is rotated by a drive mechanism consisting of belt-pulley and spur gear mechanisms. Engine power P = 5.5 kW ; engine shaft speednm = 1500 rpm ; drive pulley diameter Dt = 16 cm ; diameter of the opposite pulley Dk = 55 cm ; number of pinion teeth z1 = 21 ; number of teeth of the counter gearz2 = 60 ; pulley mechanism efficiency ηk = 0.95 ; Since the efficiency of the gear mechanism is ηd = 0.97: a) Find the output shaft speed nç and the torque Mç on this shaft.b) The force on the taut arm of the belt S1 = 450 N;coefficient of friction μ = 0.3 ; If the winding angle α = 160⁰, is the frictionally transmitted moment Ms sufficient to compensate for the Mg moment on the input shaft? Calculate.
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
A selfpropelled truck of total mass 25 tonnes and wheel diameter 750 mm runs on a track forwhich the resistance is 180 N per tonne. The engine develops 60 kW at its maximum speed of 2400r.p.m. and drives the axle through a gear box. Determine : 1. the time to reach full speed from reston the level if the gear reduction ratio is 10 to 1 Assume the engine torque to be constant and agearing efficiency of 94 per cent, and 2. the gear ratio required to give an acceleration of 0.15 m/s2on an up gradient of 1 in 70 assuming a gearing efficiency of 90 per cent.
A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 80 MPa and an angle of twist of more than 10 degrees in a length of 8 meters. G = 83 GPa
A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
B 2 ~s A single cylinder reciprocating engine has speed 240 rp.m., stroke 3 mm, mass of re ocating parts 50 kg, mass of revolving parts at 150 mm radius 37 kg. UMOO third of the reciprocating parts and all the revolving parts are to be balanced, find : 1. The bala,;: mass required at a radius of 400 mm, and 2. The residual unbalanced force when the crank g rotated 60° from inner dead centre. P e AN R eR e e g
e g O single cylinder reciprocating engine has speed 240 rp.m., stroke 3 mm, mass of reciprocating parts 50 kg, mass of revolving parts at 150 mm radius 37 kg, I MUO third of the reciprocating parts and all the revolving parts are to be balanced, find : 1. The bala,:A mass required at a radius of 400 mm, and 2. The residual unbalanced force when the crapg h; rotated 60° from inner dead centre. T e T g LSOt ULy A PO Eangt