A load P is supported by two concentric steel springs arranged as shown. The inner spring consists of 30 turns of 20 mm. diameter wire on a mean diameter of 150 mm. The outer spring has 20 turns of 30 mm. wire on a mean diameter of 200 mm. Compute the maximum load that will not exceed a shearing stress of 140 MPa in either spring. Use G = 83 GPa.

A load P is supported by two concentric steel springs arranged as shown. The inner spring consists of 30 turns of 20 mm. diameter wire on a mean diameter of 150 mm. The outer spring has 20 turns of 30 mm. wire on a mean diameter of 200 mm. Compute the maximum load that will not exceed a shearing stress of 140 MPa in either spring. Use G = 83 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
A load P is supported by two concentric steel springs arranged as shown. The inner spring consists of 30 turns of 20 mm. diameter wire on a mean diameter of 150 mm. The outer spring has 20 turns of 30 mm. wire on a mean diameter of 200 mm. Compute the maximum load in the inner spring that will not exceed a shearing stress of 140 MPa in either spring. Use G = 83 GPa. 6904 N 8810 N 9058 N 2154 N
As shown in the figure, a homogeneous 50 kg rigid block is suspended by the three springs whose lower ends were originally at the same level. Each steel spring has 24 turns of 10 mm diameter on a mean diameter of 100 mm, and G = 83 GPa. The bronze spring has 48 turns of 20 mm diameter wire on a mean diameter of 150 mm and G = 42 GPA. Compute the shearing stress in each spring, use Wahl’s Equation.
Two steel springs arranged as shown support a load P. The left spring consists of 12 turns of 20-mm diameter wire on a mean diameter of 300 mm. The right spring has 10 turns of 16-mm diameter wire on a mean diameter of 200 mm. Calculate the maximum value of P and the total elongation if the allowable shearing stress is 200 MPa. Us the Exact formula. Answer: P = 1443.35 N
Two concentric heavy steel springs support a load of 9100 N as shown in the figure. The outer spring is made from a 30-mm diameter wire on a mean diameter of 220 mm and has 22 turns. The inner spring consists of 30 turns made from 20-mm diameter wire on a mean diameter of 160 mm. Using G = 83 GPa, calculate the shearing stress developed in the two springs. τinner = ? MPa τouter = ? MPa (Provide detailed solution)
A helical spring is made by wrapping steel wire 20 mm in diameter around a forming cylinder 150 mm in diameter. Compute number of turns required to permit an elongation of 132 mm without exceeding a shearing stress of 184.8 MPa. Use G = 83 GPa.
A flexible cable and rigid boom system is used to lift a load of 65kN at the end of Boom at point C. Points A and B are considered pinned in nature. The allowable shearing stress at all bolts are 250MPa and the allowable bearing stress at all bolts are 300MPa. Note that the initial position of boom is horizontal and segment A and B are vertical. Determine the horizontal reaction at A. 3. Determine the vertical reaction at A.
The cylinder of a hydraulic ram supported at the open end is 200 mm internal diameter and is required to sustain an internal pressure of 25 MN/m2.Calculate the necessary thickness of the wall if the maximum shearing stress is limited to 55 MN/m2.Allowing for the effect of the longitudinal stress caused by the pressure on the end of the cylinder, calculate the increase in diameter due to the application of the 25 MN/m2 pressure. Take E= 214 GN/m2 and υ = 0. 28
A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150 mm. The shaft may be subjected to either a direct tensile load of 400 kN or a twisting moment of 18 kN·m. If the maximum direct and shearing stresses permissible in the bolt material are 125 MPa and 55 MPa respectively. Find the minimum diameter of the bolt required. Assume that each bolt takes an equal share of the load or torque.
The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 96MPa and the bearing stress is limited to 124 MPa. Assume the Applied load is uniformly distributed among the four rivets.
A compound tube consists of a steel tube 120 mm internal diameter and 140 mm external diameter and an outer brass tube 140 mm internal diameter and 10 mm thickness. The two tubes are of the same length equal to 150 mm. The compound tube carries an axial load of 800 kN. Estimate the stresses and the load carried by each tube and the amount it shortens. Take E for steel as 2 × 105 N/mm2 and for brass as 1 × 105 N/mm2.