Question 2Answer the following question and give justifications:a) Hassan is assigned to purchase a flow meter that can beused to measure an expected discharge of a contaminatedliquid stream from a chemical complex at a rate of 1´10*m'/day. He bought a device that has a range of 20 – 40 ft/s,would this device be reasonable? Why?b) Two students were working in a lab to determineexperimentally the viscosity of the same substance. StudentA found the viscosity to be 10.0 Pa s, and student B wasable to find the viscosity to be 6.0 lb̟ ft' s', check if bothmhave a close answer or not.c) You went to a car dealer to rent a car and you found twocars for rental, car 1 consumes 2 gallons for every 60-miledistance travelled, and car 2 consumes 1 liter for every 10km distance travelled. Which car would you choose to rent?Why?d) The following equation relates the moving mass (m) to theresting mass (m) of a particle in terms of its speed (u) andthe speed of light (c) as:Where would you place the constant c to make the equationdimensionally consistent? Why?

As per honor code and answering guidelines I can answer 1st question at a time.If you want other…

Question 2 Answer the following question and give justifications: a) Hassan is assigned to purchase a flow meter that can be used to measure an expected discharge of a contaminated liquid stream from a chemical complex at a rate of 1'10 m'/day. He bought a device that has a range of 20 – 40 ft/s, would this device be reasonable? Why?

Question 2 Answer the following question and give justifications: a) Hassan is assigned to purchase a flow meter that can be used to measure an expected discharge of a contaminated liquid stream from a chemical complex at a rate of 1'10 m'/day. He bought a device that has a range of 20 – 40 ft/s, would this device be reasonable? Why?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
Water at 80◦C flows steadily from a tank shown below at a volume flow rate of 475 L/min to a pump througha 62.7-mm diameter steel pipe. The roughness element size is 46 μm. The kinematic viscosity of water isν = μ/ρ = 3.60 × 10−7 m2/s. The tank is open to the air through a hole shown in the figure. If needed, usethe table and the Moody chart on the next page. (a) What is the pressure at the pump inlet?(b) It is desired to increase the pressure at the inlet of the pump while keeping the volume flow rate constant.If that is the only design constraint, what changes can be made to the existing system to achieve thenew design goal? List at least three suggestions.
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?
Nitrogen gas under a pressure pn = 15 psig is used for pumping kerosene at 25°C (density = 816 kg/m3, viscosity = 1.81 cP) through an elevation increase of 6 m. If there is an effective length of 45 m of nominal 2-in. schedule No. 40 pipe (commercial steel) between the two tanks, what is the flow rate of kerosene? Neglect exit kinetic-energy effects.
Please help me with this problem clearly. List two sources of error in the water-filled tube and pressure gauge method of measuring head for a hydro system and how to avoid them. Using this method, a series of measurements up a hill to the source of the stream produces the following heights: 1.5m, 0.7m, 1.0m, 1.9m, 1.6m, 0.3m, and 0.8m. What is the total head for this site? If the flow rate was 0.5 m3s-1, calculate the power available in this stream?
A fan has a suction static pressure of 40mm of water vacuum with air velocity of 5m/s. The discharge has 160mm of water gage and discharge velocity of 9m/s. What is the total head of the fan if air density is 1.2kg/m3, mm of water gauge. Answer: 203.43
Question 5 5.1 Water is pumped out of a tank through a pipe, 50mm in diameter.The dynamic viscosity of the water is 1,308 x 10-3 kg/ms.The velocity of the water in the pipe is 0.55m/s.Determine : 5.1.2 How long it will take to pump 1200 liters of water out of the tank
Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,
On a single plot, plot three curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below. Delta P on y axis and flow rate on the x axis. The pressure range is 0 to 1 MPa. (Branches 1 and 3 are in the same plane; branch 2 is located 5 m above the other two branches. Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
What is the pressure drop in the blood as it passes through a capillary 1 mm long and 2 μm in radius if the speed of the blood through the centre of the capillary is 0.66 mm/s ? (The viscosity of whole blood is 4 x 10-3 Pa.s?A. 2.6 kPaB. 10.5 kPaC. 34.5 kPaD. 23.5 kPa
Q1- The more accurate flow measuring instrument is * Flowmeter Venturimeter Rotameter Orificemeter Q2. Coefficient of discharge is the ratio of * Theoretical velocity/Actual velocity. Theoretical flow/Actual flow Actual velocity/Theoretical velocity Actual flow/Theoretical flow
What is the Reynold’s number for a flow of oil (SG = 0.80, ? = 0.00200 lb-s/ft2) in a 6-in diameter pipe at a flow rate of 10ft3/s. Is the flow laminar or turbulent? thank you!