A load P is supported by two steel springs arranged in series. The upper spring has 20 turns of ¾ in diameter wire on a mean diameter of 6 in. The lower spring consists of 15 turns of ½ in diameter wire on a mean diameter of 5 in. Determine the maximum shearing stress in each spring if the total deflection is 3 in. and G=12x106 psi. Clean and detailed solution. Thank you.

A load P is supported by two steel springs arranged in series. The upper spring has 20 turns of ¾ in diameter wire on a mean diameter of 6 in. The lower spring consists of 15 turns of ½ in diameter wire on a mean diameter of 5 in. Determine the maximum shearing stress in each spring if the total deflection is 3 in. and G=12x106 psi. Clean and detailed solution. Thank you.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
Problem 1: A circular shaft with a diameter of 100 mm and a length of 2 meters is subjected to a torsional moment of 500 Nm. The shaft is made of a material with a shear modulus of 80 GPa. Determine the maximum shear stress and the angle of twist along the length of the shaft. Problem 2: A solid circular shaft of length 3 meters is made of a material with a shear modulus of 60 GPa. The shaft has a diameter of 80 mm and is subjected to a torque of 600 Nm. Due to manufacturing constraints, the maximum allowable shear stress for the material is 60 MPa. Determine if the shaft design is safe and, if not, suggest an alternative design to meet the given constraints.
2. A hollow shaft and a solid shaft constructed of the same material have the same length and the same outer radius. The inner radius R of the hollow shaft is 0.6R. Assuming that both shafts are subjected to the same torque, compare their shear stresses, angle of twist and weights. 3. A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside diameter 82mm. The tube is 2.75m long and the aluminium has shear modulus G=28GPa. a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist (in degrees) when the maximum shear stress is 48 MPa.b. What diameter d is required for a solid shaft to resist the same torque with the same maximum stress.c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
A spring (squared and ground) having a pitch 0.75 inch has a mean diameter of 1.5in and a wire diameter of 0.25in. After applying a certain load, the spring deflects 0.5in with a corresponding stress of 30.75 ksi. The spring is to be made of tempered steel wire having a shear modulus of 12 million psi.
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
a) The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion) i) The second moment of area relative to z-axis, I_z, for the cross-section can be calculated as ( Enter your answer in cm4 ii) The bending stress at Point H can be calculated as (Enter your answer in MPa, Compressive stress is negative and tensile stress is positive) iii) The first moment of area required to calculate shear stress at H can be calculated as (Enter your answer in mm^3) iv) The absolute value of the transverse shear stress at point H can be calculated as (Enter your answer in MPa ) v) Maximum principal stress can be calculated as (Enter your answer in MPa ) vi) Minimum principal stress can be calculated as (Enter your answer in MPa ) vii) The equivalent stress for Maximum-Shear-Stress Theory ( Tresca criterion) (Enter your answer in MPa ) b) The von Mises equivalent stresses at point H can be calculated as: MPa c) The factors of safety at point H…