A long shunt compound Generator supplies 9.6 kW at a terminal voltage of 200 V. The machine parameters are as follows: Ra = 0.2 N, Rs = 0.3 N, Rsh torque developed by the prime mover is 116N.m, find the following after drawing the circuit diagram: 1. Copper loss, 2. Iron and friction loss, = 100 N. If the total losses are 2000 W and the 3. Overall efficiency 4. Speed in r.p.m.

A long shunt compound Generator supplies 9.6 kW at a terminal voltage of 200 V. The machine parameters are as follows: Ra = 0.2 N, Rs = 0.3 N, Rsh torque developed by the prime mover is 116N.m, find the following after drawing the circuit diagram: 1. Copper loss, 2. Iron and friction loss, = 100 N. If the total losses are 2000 W and the 3. Overall efficiency 4. Speed in r.p.m.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

A transformer has a turn ratio of 15:1. If the primary voltage is 7.2KV line-to-line, the primary current is 150 A, and series impedance of the secondary side is 3+j4 ohms, which of the following statements is true? Assume the stator and rotor magnetic fields of a motor, “BS” and “BR,” are in x-y plan. If the angle from the vector BS to BR is 30o, measured counterclockwise, what would be the direction of the resulting induced torque? A. clockwise B. Along the -z axis C. counterclockwise D. In the x-y plane E. Along the +z axis
A turbine has a power coefficient equal to 0.3 when the wind speed is 7 m / s. This turbine is coupled, through a multiplier, to an asynchronous generator of rotor in cage which, in turn, is connected to the distribution network. Considering the data, Air density: 1.25 kg / m3 Blade radius: 15 m Multiplier coefficient: 50 Number of asynchronous generator's pole pairs: 2 Mains frequency: 60 Hz 1% slip Calculate the speed of the turbine rotor (rpm). Is it considered fast or slow?
The wind turbine gives the following data: Blade length, l = 49 m, Wind speed, V= 32 Km/Hr, Air density, ρ = 1.23 kg/m3 , Power Coefficient, Cp = 0.4, Calculate the power available in the rotor in Watts. 60772464.72 W 394985.47 W 1302564.83 W 151931161.80 W
A 19 kVA, 419 V, 50-Hz, 3-φ, star-connected synchronous generator gave the following test data : Field current (A): 2 4 6 7 8 10 12 14 Terminal volts: 155 287 395 440 475 530 570 592 S.C. current : 11 22 34 40 46 57 69 80 Resistance between any two terminals is 0.3 Ω Find regulation at full-load 0.8 p.f. lagging by synchronous impedance method. Take ZS corresponding to S.C. current of 80 A.
Q2. The O.C.C for a shunt generator at (1000 r.p.m) given by:lf(A) 0.2 0.5 1.0 1.5 2.1 2.4 3 4.2 4.8E(V) 28 72 144 202 245 270 300 345 360The armature resistance equal (0.5 ohm) and shunt field resistance equal (83.33 ohms). If the machine is driven at (1100 r.p.m) find:(a)The load current if the load resistance equal (9 ohms). (b)The number of series winding to convert the machine to level compound at (345 V) at armature .current of (100 A)
If the Reactance of the cylindrical rotor machine connected to an infinite bus bar is double that of the external reactance of 0.5.p.u. If the power angle is 35°, real power output is 0.8, compute the excitation voltage, and for the same power output, if the load angle is reduced by 10 degrees, find the external reactance to achieve this.
The flux density distribution in the air-gap of a 50 Hz alternator is given by the expression B=B1msinθ+(B1m/3)sin3θ. The armature winding, which can be assumed to be uniformly distributed, is a 3-phase, narrow-spread, full-pitched winding with 120 turns per phase. If the total flux per pole is 0.1 Wb, calculate the rms value of the emf per phase and the form factor of the phase emf. (2345 V,1.06)
A shunt generator has the following open-circuit characteristic at 800 r.p.m.Field amperes : 0.5 1.0 1.5 2.0 2.5 3.0 3.5E.M.F. Volt : 54 107 152 185 210 230 245Armature and shunt field resistances are respectively 0.1 Ω and 80 Ω. The terminal p.d. falls to 175 Vwhen the armature current is 100 A. Find the O.C. volts and the volts lost due to (i) reduction in the fieldcurrent (ii) armature resistance (iii) armature reaction.
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit impedance of the load. Select one: a. 1736 (45 degree) Ohm b. 36 (90 degree) Ohm c. 1.736 (30 degree) Ohm d. None of the above
Question # 2 A 3-phase, 2300 V, 2000 KVA, 50 Hz, star connected synchronous generator has the following parameters: p.f.= 0.8 Lagging, Poles = 2, Ra / phase = 0.15 Ω, Xs / phase = 1.1 Ω, PF&W = 24 KW, PCORE = 18 KW, VF = 200 V, IF = 10 A, R F = 20 – 200 Ω Calculate: a) Internal generated voltage? b) Torque angle? c) Generator’s prime mover output? e) % age Voltage Regulation? f) Approximate power of generator? g) Static Stability Limit? h) Phasor Diagram?
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit current in the line Select one: a. 1.43 A b. 0.569 A c. None of the above d. 2.01
A 800 V, 120kVA, 3-phase, 50 Hz, salient-pole synchronous generator is used in a hydroelectric dam, converting water flow into electricity via a turbine. The reactance values (Xd and Xq) are 1.95 Ω and 1.10 Ω, respectively and the terminal current is measured to be 95 A at a power factor of 0.85 lagging. The armature resistance can be considered to be negligible (Ra =0). a) Draw the phasor diagram of the generator, b) Compute the generated voltage (Êaf) when the generator delivers its rated kVA at 0.85 lagging power factor and rated terminal voltage. ANS=Eaf=578.05exp(j9.75°)