A machine sbop uses two lathes to make shafts for electnc motors. A sample of five shafts from each lathe are checked for quality-contral purposes The diameter of each shaft (n inches) is given as follows Lathe Lathe II 0 501 0 503 0.498 0.504 0302 0.495 0.497 0.497 0.502 0.501 The mes diamrter in cach sample is 0 500 Find the staodard deiation for the saniple of shafts checked fom Lathe 01 nd Lathe 02 Which lathe is mere comsttand why

A machine sbop uses two lathes to make shafts for electnc motors. A sample of five shafts from each lathe are checked for quality-contral purposes The diameter of each shaft (n inches) is given as follows Lathe Lathe II 0 501 0 503 0.498 0.504 0302 0.495 0.497 0.497 0.502 0.501 The mes diamrter in cach sample is 0 500 Find the staodard deiation for the saniple of shafts checked fom Lathe 01 nd Lathe 02 Which lathe is mere comsttand why

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter16: Table Of Decimal Equivalents And Combined Operations Of Decimal Fractions

Section: Chapter Questions

Problem 36A: A slot is machined in a circular plate with a 41.36-millimeter diameter. Two milling cuts, one 6.30...

See similar textbooks

Similar questions

Compute the cross-sectional area of the grooved block shown. Round the answer to 1 decimal place.
Four studs of the following lengths in inches are to be machined from bar stock: 134,178,2516 and 11132 . Allow 18inch waste for each cut and 132inch on each end of each stud for facing. What is the shortest length of bar stock required so that only three cuts are needed?
Compute the area of the steel insert (shaded segment) shown. Round the answer to 1 decimal place.
A slot is machined in a circular plate with a 41.36-millimeter diameter. Two milling cuts, one 6.30 millimeters deep and the other 3.15 millimeters, are made. A grinding operation then removes 0.40 millimeter. What is the distance from the center of the plate to the bottom of the slot? All dimensions are in millimeters.
The farmer in Exercise 33 has decided to take the fencing purchased and use it to enclose the subdivided plots shown. aWhat are the overall dimensions of the rectangular enclosure shown? bWhat is the total area of the enclosure shown?
As in Exercise 39, find the volume of the box if four congruent squares with sides of length 6 in. are cut from the corners of a rectangular piece of poster board that is 20 in. wide by 30 in. long. Kristine creates an open box by cutting congruent squares from the four corners of a square piece of cardboard that has a length of 24 in. per side. If the congruent squares that are removed have sides that measure 6 in. each, what is the volume of the box formed by folding and sealing the flaps?
An igloo or Eskimo hut is built in the form of a hemispherical shell with an inside diameter of 12 ??. If the igloo is constructed of snow blocks having a uniform thickness of 2 ?? and weighing 40 ?? ??? ??. ??, find the weight of the igloo, neglecting the entrance. Also, if fresh air contains 0.04 percent carbon dioxide, find the amount of this gas in the igloo when freshly ventilated.
A 6sided die is rolled find p(3or 5)?
A regular hexagonal shaped target with sides of length 14 cm has a circular bull’s eye with a diameter of 3 cm. For 18-21, assume darts are thrown and hit the target at random. Round answers to the nearest thousandth. 21. Estimate how many times a dart will hit the new bull’s eye if 50 darts hit the target.
A Normal window is in the shape of a rectangle surmounted by a semi-circle. Whatis the ratio of the width of the rectangle to the total height so that it will yield awindow admitting the most light for a given perimeter?
The operations manager of a plant that manufactures tires wants to compare the actual inner diameters of two grades of tires, each of which is expected to be 575 millimeters. Samples of five tires from each grade were selected, and the results representing the inner diameters of the tires, ranked from smallest to largest, are shown below. Complete parts (a) through (b) below.
For a fabric, the number of defects per square yard is counted on 100 samplespecimens, each 1 square yard in size. The results are as follows: