A machine shaft supported on bearings 2 m apart is to transmit 180 KW at 200 rpm while subjected to a reversed bending load of 5000 N located at a distance of 60 cm from one bearing. Allow a shear stress of 40 MPa and a bending stress of 80 MPa, determine the shaft diameter for steady loading if km = 1.5 and ks = 1.0. note: answer must be in mm

A machine shaft supported on bearings 2 m apart is to transmit 180 KW at 200 rpm while subjected to a reversed bending load of 5000 N located at a distance of 60 cm from one bearing. Allow a shear stress of 40 MPa and a bending stress of 80 MPa, determine the shaft diameter for steady loading if km = 1.5 and ks = 1.0. note: answer must be in mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Similar questions

A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A 3-m steel shaft is to transmit 100 kW at 300 rpm. It carries two gears each weighing 1.9 kN supported at a distance of 1 meter from each ends. Assuming an allowable shaft bending stress of 117 MPa, determine the diameter of the shaft in mm using ASME code (assume Km = 1.0 and Kt = 1.0)
The maximum bending stress of a hollow shaft is equivalent to 80N/mm2, while the maximum shear stress is equal to 70 N/mm2.The shaft rotates and loads are applied suddenly, with minor shocks. Determine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending moment of 2100 N-m and a torque of 4100 N-m if the thickness of the hollow shaftis equal to 0.15of the outer diameter of the shaft. Apply ASME Code for this problem.
Calculate the shaft diameter and torsion angle since the maximum torsional moment is 150 Nm for a 1 meter long shaft with a permissible shear stress of 320 MPa G=80 GPa
he maximum bending stress of a hollow shaft is equivalent to 80 N/mm2, while the maximum shear stress is equal to 70 N/mm2. The shaft rotates and loads are applied suddenly, with minor shocks. Determine the outer and inner diameter (in mm) of a hollow shaft that is required to carry a bending moment of 2100 N-m and a torque of 4100 N- m if the thickness of the hollow shaft is equal to 0.15 of the outer diameter of the shaft. Apply ASME Code for this proble
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
A 16 ft steel line shaft has no bending action except its own weight. What power in hp can shaft deliver at a speed of 200 rpm. Consider that the torsional deflection wm not exceed 0.08o/ft of length.