A Machine vice has single start square threads with nominal diameter 22 mm and pitch 5 mm. Collar diameters are 55mm and 45mm respectively. Coefficient of friction for threads 0.15 and u for collar 0.17 The machinist can comfortably apply a force of 125N on handle of mean radius 150 mm. Assuming uniform wear theory calculate, (1) The clamping force developed between the jaws, (2) The overall efficiency of screw

Q: xaplin with illustrations, slip via dislocation motion (edge abd screw dislocation) and twinning

A: To explain: Slip via dislocation motion (edge and screw dislocation) and twinning.

Q: The beam AB supports two concentrated loads P and Q. The normal stress due to bending on the…

A:

Q: Question 1: Consider an electric refrigerator located in a room. Justify and determine the direction…

A: An electric refrigerator is a device which transfer heat from the lower thermal reservoir to the…

Q: A spring-loaded piston-cylinder device contains 2 kg of carbon dioxide. This system is heated from…

A: (2) Given, The mass of CO2 is 2kg. The initial pressure of the gas, P1=180kPa The initial…

Q: If the gap between C and the rigid wall at D is initially 0.08 mm, determine the support reactions…

A: Given data: Deformation, δ=0.08 mm The value of, P=500 kN Young modulus, E=200 GPa. Calculate the…

Q: Required information Three boards are nailed together to form a beam that is subjected to a vertical…

A:

Q: The drums have the angular velocities at the instant shown in (Eigure 1). Assume w 2 rad/s. TB=0.20…

A: GivenωA=2 rad/srB=0.20m

Q: 6. As shows in the picture, the two ends of shaft are fixed, the torsion stiffness GI, is constant.…

A:

Q: P.4: R(s) + E(s) K(s+7) s(s+5)(s+8)(5+12) C(s) a. What value of K will yield a steady-state error in…

A:

Q: If the tension of the force P is 500 lb, determine: a) the X, Y, Z components of the force exerted…

A:

Q: 17-35. The dresser has a weight of 80 lb and is pushed along the floor. If the coefficient of static…

A:

Q: Oil (Specific gravity = 9, ν =1.0*10-5 m2/s) is transported through a plastic pipe of 500 m in…

A:

Q: Member AB has the angular velocity WAB = 4 rad/s and angular acceleration AB = 6 rad/s². (Figure 1)…

A:

Q: A box of height 7 m and a square base of side 4 m is submerged in a pool of water. The top of the…

A: Givenboxh=7ma=4mx=3mρ=1000 kg/m3g=9.81 m/s2

Q: What is the pressure of air (lb/ft2) on a standard day at 20,000 ft? Group of answer choices 72…

A: Given  height h= 20000 ft

Q: Explore the profiles of both radial plate and cylindrical cams that will achieve a specified motion.

A: To explore: The profiles of both radial plate and cylindrical cams that will achieve a specified…

Q: room temperature plastic deformation of pure lead (pb), with recrystallization temperature of -4,…

A: To choose: The correct option.

Q: Which of the followings is NOT correct: Question 4 options: 1.The constants C2 and C3, which appear…

A: To choose: The incorrect option.

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A: Given: Find: Using method of joints, the force in each member of truss.

Q: Q6/ Air is he of heat transf velocity and Disregarding static pressur

A: Given data Amount of heat transfer = 60kJ/kg Velocity of air V2=620 m/sec static pressure P2=270 kPa…

Q: A sliding block C moves along horizontal line AC. A rotasting arm AB is '4 ft. 3.in. long and…

A: Given: Crank length, AB=4 ft 3 in=52 inches Connecting rod, BC=8 ft=96 inches Extension link, BD=45…

Q: A schematic of a combined refrigeration cycle and a portion of a steam power cycle is shown in the…

A: m_3 = 3[kg/s] P[1] = 5000[kPa]T[1] = 350[C] P[2] = 2000[kPa]T[2] = 250[C] P[3] = 200[kPa]x[3] =…

Q: Most commodity thermoplastics are derived from the ethylene polymer family. O True False

A: To check: The given statement.

Q: uppose that Pi = 4.4 kN and P2 = 3.3 kN. (Figure 1). Determine the force in members GF , CF, and CD…

A:

Q: Bolts installed on a production line are tightened with automatic wrenches. They are to be tightened…

A: Hi, You have uploaded more than one question. We can solve first question for you since the exact…

Q: Consider a refrigeration system that operates on an actual vapor-compression refrigeration cycle…

A: Given:Refrigerant=R134aIsentropic efficiency of a compressor, ηisen=75.1%Refrigerant inlet condition…

Q: 3. The pin joint shown below experiences forces to the left and right of 1.14 kN as shown. Find the…

A: given : shear load P = 1.14 kN Shear stress τ = 594 kN/m²

Q: The difference between the ideal versus the actual vapor-compression refrigeration cycle can be…

A: Given: The difference between the ideal versus the actual vapor-compression refrigeration cycle can…

Q: A cast-iron beam has the cross-sectional dimensions shown in the figure. If the allowable stresses…

A: Givenσyt=50MPaσyc=250MPaτy=55MPa

Q: P.5: For the unity feedback system shown K(s + a) (s+B)² G(s) is to be designed to meet the…

A:

Q: Air enters a frictionless duct with V₁ = 70 m/s, T₁ = 600 K, and P₁ = 350 kPa. Letting the exit…

A: To Find : The entropy change at intervals of 200 K. Given : The inlet velocity is v1=70 ms The…

Q: A stainless steel rod (AISI 304) of length L = 100 mm and triangular cross section is attached…

A: Given-Information:- Length, L = 100 mmTx=0=Tx=L=50°CPerimeter,P=5.25 mmT∞=23°CTx=0.5L = 25°CT ¯= 310…

Q: The muffler is engineered as an acoustic soundproofing device designed to reduce the loudness of the…

A:

Q: Show the ts diagram and complete and step by step solution. Thermodynamics subject.

A:

Q: Question 4: An insulated room is heated by burning candles. Is this a heat or work interaction? Take…

A: According to Bartleby guidelines we can solve only one questions at a time. You are requested to…

Q: 2-7 4)Find true magnitude and direction of forces on the wheel and cable members at static…

A: Solution:

Q: Determine: Magnitude Direction Position Of the resultant of the system of forces acting a plate. As…

A:

Q: A force of F = 13 kips is applied as shown in the figure below. If the diameter of the bolt is d =…

A: Given data:- force (F) = 13 kips  the diameter of the bolt (d)= 1.4 inches, To find:-the maximum…

Q: From pump 1.0 m 1.5 m a. Using a vertical bar chart, plot the pressure drop (i.e. P₁-P₂) for these…

A:

Q: Liquid A has a density of 0.85 kg/m3 and a specific sensible heat capacitance (Cv) of 2.2 kJ/kgK.…

A:

Q: 1. Three vertical wires each 4.5m long hang in the same vertical plane from a horizontal ceiling and…

A:

Q: W1 L₁ B L2 W2

A:

Q: Consider the mechanical system shown in the figure below. Suppose the system input u is the velocity…

A:

Q: A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of…

A: According to the given data Diameter=d=8mm Change in diameter (∆d )= 5×10-3 mm  Young's modulus E =…

Q: 1. A cylindrical air compressor tank with an inside diameter of 600 mm has a safe working pressure…

A: Given data  Diameter= 600mm Pressure= 1 MPa  Tensile stress = 75 MPa  Find the thickness of the wall…

Q: Determine the forces in members AD and DG. The forces are positive if in tension, negative if in…

A: Solution: Given Data: h=1.7d   To Find: (a) Force in member AD. (b) Force in member DG.

Q: A 340 L tank contains steam, initially at 400°C, 3 bar. A valve is opened for 20 seconds and steam…

A: GivenV=340L=0.340 m3T1=400oCP1=3 bart=20sm˙o=-0.005 kg/s

Q: For the beam and loading shown, determine horizontal deflection at A using Castigliano's theorem…

A:

Q: Please describe the most important aspects of RAC and explain why you should make use of it.

A: RAC (Refrigeration and Air Conditioning) is an important technology that is used in various…

Q: Solidworks part Units: IPS Any sort of assistance on understanding how to build this part would be…

A: It is asked to create a Solidworks model of the image given

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.