Solidworks part Units: IPS Any sort of assistance on understanding how to build this part would be appreciated.

Q: 3. A boy is swinging as shown below. When = 50°, his velocity is moving downward at v = 10 ft/s. The…

A: Given: mass m = 1.95 slugs velocity v  =10 ft/s radius , r = 10 ft angle = 500 To find:

Q: Draw Shear and moment diagrams for the beams loaded as shown below:

A: To find out:- Shear Force Diagram Bending Moments Diagram

Q: a. b. Figure 2 shows another ball-and-stick model of a very small crystal of a- Polonium, but this…

A: Given: To find: Number of bonds broken to move by slip by one unit of b from left to right

Q: A force of F = 13 kips is applied as shown in the figure below. If the diameter of the bolt is d =…

A: Given data:- force (F) = 13 kips  the diameter of the bolt (d)= 1.4 inches, To find:-the maximum…

Q: 2..Assume that the cable GBH is replaced by a cable GB only (TBH-0). So the frame ACD is supported…

A: The free body diagram for the frame ACD is given below,

Q: Air enters a nozzle with a velocity of 50 m/s and a temperature of 150°C and exits with a velocity…

A:

Q: The air transport B is flying with a constant speed of 445 mi/hr in a horizontal arc of 9.1-mi…

A: To Find : The acceleration of A as measured by an observer in and turning with B. Given : The speed…

Q: 1 200mm 1 2₁.965 140mm RI 200 mm 1100mm 80mm son/m ←300mm + ↑ ک۹۰ 4. ✓ гном T Rz 7

A:

Q: Liquid water flows isothermally at 20°C through a one-inlet, one-exit duct operating at steady…

A: Given: The inlet diameter d1=0.025 m The exit diameter d2=0.3 m The inlet velocity v1=45 ms The…

Q: Bolts installed on a production line are tightened with automatic wrenches. They are to be tightened…

A: Hi, You have uploaded more than one question. We can solve first question for you since the exact…

Q: The signboard truss is designed to support a horizontal wind load of 660 lb. If the resultant of…

A:

Q: alyse the holding torque and power transmitted through epicyclic gear trains

A: To analyse: Holding torque and power transmitted through epicyclic gear trains.

Q: A sphere has a radius of 0.100 m. Its surface can be treated as a grey surface with emissivity 0.20…

A:

Q: For the beam shown, find the reactions at the supports and plot the shear-force and bending moment…

A: According to the given data A loading beam OABCD We need to find Reactions and Shear force and…

Q: 7.17 Air at a pressure of 1 atm and a temperature of 50°C is in parallel flow over the top surface…

A:

Q: Examine the way manual welding is performed and challenge it's purpose place sequence and method of…

A: Manual welding is a welding process that involves the use of a welder to join two pieces of metal…

Q: Problem 5: The solid 1.5-in.-diameter steel [E = 29,000 ksi] shaft shown supports two pulleys. For…

A:

Q: The flow stress of a coarse-grained dilute copper alloy increased from 2 to 55 MPa when the…

A: according to the given detail:

Q: how would you adjust the horizontal plane

A: The horizontal plane is a geometric plane that is perpendicular to the direction of gravity and…

Q: Consider pressurized water, engine oil (unused), and Nak (22%/78%) flowing in a 20-mm-diameter tube.…

A: To Find: The mean velocity the hydrodynamic entry length at temperature T=366 K. Given : The fluid…

Q: The cantilevered handle in the figure is made from mild steel that has been welded at the joints.…

A: Given: To find: Vertical deflection at the tip

Q: Problem 6. Fox Fork Fabrication Fox Factory Inc. is testing a new fork design. A step force of F=…

A:

Q: Water flow through the horizontal D₂=8 cm Y-branch shown in figure. Calculate the vertical force…

A:

Q: 40808805 WAB 2m B 3m 30° C Vc = 4m/s If the block at C is moving downward at 4 m/s, determine the…

A:

Q: What safety precautions should be taken during welding and cutting operations?

A: Welding and cutting operations can be extremely hazardous if proper safety precautions are not…

Q: A canister of sevoflurane, an inhaled anesthetic, is warmed to room temperature over the course of…

A: Given that, Force exerted by the piston, F= 623mN Volume increase,  dV = 16cm3 We have to find work…

Q: what is the cop

A:

Q: B.33 Determine the mass moment of inertia of the steel machine element shown with respect to the…

A:

Q: Question 4: An insulated room is heated by burning candles. Is this a heat or work interaction? Take…

A: According to Bartleby guidelines we can solve only one questions at a time. You are requested to…

Q: Solidworks part Units: MMGS Primarily just need help understanding how to interpret the holes on…

A: It is asked to interpret holes to sketch them in Solidworks

Q: The drums have the angular velocities at the instant shown in (Eigure 1). Assume w 2 rad/s. TB=0.20…

A: GivenωA=2 rad/srB=0.20m

Q: LAD 2: 000 001 -LEQ Less Than or Eql Source Source B N7:7 0 360 0168h What value must be in N7:6 for…

A: The ladder logic diagram shows a simple program to control the output O:2/4 based on the value in…

Q: Required information A polystyrene rod consisting of two cylindrical portions AB and BC Is…

A: The given information in the problem is shown in the following attached image:

Q: Question 1: Consider an electric refrigerator located in a room. Justify and determine the direction…

A: An electric refrigerator is a device which transfer heat from the lower thermal reservoir to the…

Q: Part A Consider the beam shown in (Figure 1). Suppose that the distributed load w = 700 lb/ft Follow…

A:

Q: Determine the pin reachions at pin A, B, and C in the frame shown. Neglect the weight of the…

A:

Q: Consider the frame shown in (Figure 1). Suppose that F₁ = 17 kN. Figure 2 m D A ·x 1.5 m B 1.5 m

A: The given information in the problem is shown in the following attached image:

Q: iven an element with stresses as indicated in figure below, find the following: a) The maximum and…

A: Given: The shear stress acting on the element = -35 kPa The normal stress along the x-axis = 20 kPa…

Q: We have a machine called automated candle machine using pneumatic press. What are the methods of…

A: To determine: The methods of determining the operating time of scraping time, grater time and…

Q: 3. An unknown gas moving at a constant speed of 164 m/s enters a tube of constant cross sectional…

A: (a) Write the given data. v=164 m/sm˙i=3 kg/sPcr=767 kPaTcr=140 °Cγ=1.289R=0.1889 kJ/kgK

Q: A 1.2 m steel pipe 9 mm thick carries water at a velocity of 1.83m / s . The pipe line is 3050 m…

A: To Find : The maximum rise in pressure. Given : The velocity is v=1.83 ms The lenght of pipe is…

Q: One way to define forging procedures is by the extent to which the work is constrained in the die.…

A: This question is based on the concept of forging .

Q: Show the mass of a flywheel needed to keep a machine’s speed within specified limits

A: To show: The mass of a flywheel is needed to keep a machine’s speed within specified limits.

Q: Using this equation FL/AE Q1/The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of…

A:

Q: An aircraft flying at a geometric altitude of 22,000 ft has instrument readings of P = 880 lb/ft²…

A: Solution: Given Data: H=22000 ftP=880 lb/ft2T=430oR   To Find (a) Find hP, hT and hρ? (b)…

Q: Using the ‘basin of attraction’ model and associated discussion in Walker et al, is the conversion…

A: To find: Whether the conversion from internal combustion engines to electric vehicles an example of…

Q: A 340 L tank contains steam, initially at 400°C, 3 bar. A valve is opened for 20 seconds and steam…

A: Given data:- Volume of tank =340 L Temperature =400 °C Pressure =3 bar A valve is opened for= 20…

Q: For the system shown a step torque is applied at 0₁(t). Given J and k1Nm. Find: = rad 1. The…

A:

Q: Example 5&6.5: Water is drawn into the pump, such that the pressure at the inlet A is -30 kPa and…

A:

Metal Casting

Metal casting is described as a manufacturing process in which a mold cavity is produced by sand, and molten metal is filled inside a mold cavity. The desirable shaped object is achieved after the solidification of molten metal. Large metal objects like machine beds, motor bodies, and others can easily be manufactured using metal casting. The place or shop where metal casting is performed is called foundry.