A medical equipment that will be used by virologist to determine the categories of COVID 19 disease in Ghana has a unity feedback system. If this system has a damping ratio is 0.75, and an open-loop transfer function as shown below. 3K G(s) (s + 1)(s+ 5) Then, determine: i. The value of the system parameter, K. ii. The peak overshoot. iii. The time to peak overshoot. 5 iv. The settling time at 5% tolerance band.

A medical equipment that will be used by virologist to determine the categories of COVID 19 disease in Ghana has a unity feedback system. If this system has a damping ratio is 0.75, and an open-loop transfer function as shown below. 3K G(s) (s + 1)(s+ 5) Then, determine: i. The value of the system parameter, K. ii. The peak overshoot. iii. The time to peak overshoot. 5 iv. The settling time at 5% tolerance band.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given an inverting amplifier having a gain of 40 dB if the feedback capacitor is 10 pFDetermine the input and output Miller capacitance.Please show the complete solution
a) Illustrate the pole-zero plot for the systemb) Identify the differential equation for the systemc) Analyze the system for Causality and Stabilityd) Infer the impulse response for the system. (Inverse H(s))e) Give block diagram for series and Parallel interconnection of the system (2 diagrams)
The filtering stage of a biomedical device passes signals with frequencies ranging between 20 Hz and 500 Hz while the stage delivers a total gain of 48 Design the electronic circuit of the filtering stage using appropriate numbers of operational amplifiers,resistors, and capacitors. (The filtering are all 1st order active filters and the maximum possible gain is limited to 10 for a single amplifier) B. In the circuit, the capacitors are all 318 nF and the feedback-resistors are all 10 k.ohm find the values of the remaining resistors in the circuit
The control system manages, commands, directs, or regulates the behavior of other devices or systems using control loops. State the advantages of implementing negative feedback in a closed-loop system. Then Write the corresponding differential equation for the transfer function given, Specify the assumption made for the solution.
Electrical Engineering For a unit feedback system having the following gain functions: G(s) Ks - 4.21) s² (2 s +5.7) 2 (1) Draw the root trajectory. (2) Find the value of the gain K in which all three roots are real and have intermediate roots. (3) When it becomes as in (2), find the value of its root. -thanks you very much for the help ~~
For the following first-order system, G(s) = 11/(s+19)Let: τ - time constanttr - rise timets - settling timeK - DC gainDetermine the value of 2τ + 2tr + 2ts + 2K
a) What is the currenr flowing in the input resistor (i1) for t>0? b) What is the value of the feedback resistor Rf? c) What is the capacitor voltage in steady state (Vc( ∞ ))?
For the electric circuit given in the figure;a) Obtain the transfer function between V2(s) and V1(s).b) Calculate the gain value and time constant of the system in steady state as C=2MicroFarad, R1=R2=1Mohm.c) According to the values given in option B, obtain the expression to be obtained at the output for the unit step input by using the residual sum method.
Determine the pole-zero plot of the impulse response of a single pole causal LTI system below.
The circuit shown can be used as a variable capacitor, where CM can be tuned by changing the resistor RTUNE. All op-amps are ideal. a) Use the Miller theorem to find the expression for CM b) Find the required value for RTUNE so that CM=100 nF
Determine the pole-zero plot of the impulse response of a single pole causal LTI system given in the picture
From transfer function used in simulation, calculate all step response characteristic parameters and compare your result with value obtained from Assignment