A message signal m(t) =c(t) = 100 cos(2n10°t) with k,10 cos(2000nt) frequency modulates the carrier signal= 150.a) Find the modulated signal expression in terms of the Bessel function.b) What is the modulated signal expression in terms of Bessel function if we want toinclude the minimum number of harmonics needed for the effective bandwidth tocontain at least the %95 of the modulated signal power? (Note: Use the table given inthe second page)c) What is the output of the filter h(t) = 12000 sinc(3000nt) e2#10°t when the signalin 3.b is given as its input?

Answered: Image /qna-images/answer/6ed66072-af33-49cf-ac64-d976128a105e.jpg

A message signal m(t) c(t) = 100 cos(2n10°t) with kf = 150. = 10 cos(2000nt) frequency modulates the carrier sign a) Find the modulated signal expression in terms of the Bessel function. b) What is the modulated signal expression in terms of Bessel function if we want include the minimum number of harmonics needed for the effective bandwidth contain at least the %95 of the modulated signal power? (Note: Use the table given the second page) c) What is the output of the filter h(t) = 12000 sinc(3000nt) e1210°t when the sign in 3.b is given as its input?

A message signal m(t) c(t) = 100 cos(2n10°t) with kf = 150. = 10 cos(2000nt) frequency modulates the carrier sign a) Find the modulated signal expression in terms of the Bessel function. b) What is the modulated signal expression in terms of Bessel function if we want include the minimum number of harmonics needed for the effective bandwidth contain at least the %95 of the modulated signal power? (Note: Use the table given the second page) c) What is the output of the filter h(t) = 12000 sinc(3000nt) e1210°t when the sign in 3.b is given as its input?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A given FM transmitter is modulated with a single sinusoid, the output for no load power is 100W into 50Ω resistive load. Then, the frequency of the modulating signal is carefully adjusted from zero until the modulated carrier encountered its zero amplitude as observed in spectrum analyzer. Under these conditions, determine the: (Use the provided Bessel table) a. the modulation index and the number of significant sideband b. total power on its significant sidebands. c. relative total power of the carrier and each of sideband. Ans. (a) Mf =2.4, N=5; (b) 99.86 W; b Pc=0W, P1=27.04W, P2=18.49W, P3=4W, P4=0.36W, P5=0.04W
The modulating signal that is the input into an FM modulator is m(t)=2cos(10??).a) Express the time domain expression of ?(?) signal.b) Express FM signal in terms of Bessel functions.c) Sketch the frequency spectrum of the modulated signal.d) Determine the bandwidth of ?(?) occupies 98% of the total power (Carson Rule) in the acquired spectrum.e) Determine the condition of required bandwidth of ideal BPF if at least 80% of the total power appears at the output of the filter?
Write the equation for the Power Spectral Density of the filtered signal ?
An FM transmitter is determined to have a transmitter sensitivity of 498.716Hz/V. If the modulating signal is designed to be 15.998V, and the modulation index is kept to be at 1.5, solve for the highest upper sideband frequency in MHz considering that the carrier signal has a frequency equal to 172.255MHz.
For an Armstrong indirect FM transmitter with the crystal carrier oscillating at 210 kHz, the crystal reference oscillating at 10.2 MHz, the sideband voltage is 0.018 V, the carrier input voltage to the combiner is 5V, the first and second multipliers are both 40, and the modulating signal frequency is 2 kHz, determine: a.) modulation index at the output of the combining network and the power amplifier; b.) frequency deviation at the same two points; and c.) the transmit carrier frequency.
Type your question here Determine the power in the sidebands as a percentage of the total power of a modulated signal in the case of a carrier – amplitude – modulated by two sinusoidal signals of different frequencies, with individual modulation depths of 0.3 and 0.4.
4. short answers a. What is the effective antenna area of an antenna at 2500 MHz, if the gain is 13 dBi. b. For a WCDMA handset with 7 dB noise figure and 5 MHz effective noise bandwidth, calculate the noise floor in dBm. c. An NBA basketball player is close to 2 meters tall, and an “Umpa-Lumpa” from the movie “Willie Wonka” is 0.5 meters tall. Assuming 2-ray propagation model, what is the ratio of the signal strength received by the two people? d. Consider a 12-km microwave link with 15 meter towers at both ends, calculate the minimum frequency in GHz, such the first Fresnel zone does not intersect the ground? Assume that the ground is flat between the towers.
A given FM transmitter is modulated with a single sinusoid, the output for no load power is 100W into50Ω resistive load. Then, the frequency of the modulating signal is carefully adjusted from zero untilthe modulated carrier encountered its zero amplitude as observed in spectrum analyzer. Under theseconditions, determine the: (Use the provided Bessel table)a. the modulation index and the number of significant sideband. b. total power on its significant sidebands. c. relative total power of the carrier and each of sideband. Ans. (a) Mf =2.4, N=5; (b) 99.86 W; b Pc=0W, P1=27.04W, P2=18.49W, P3=4W,
Chose the correct answer 6- The bandwidth required for a modulated carrier depends on: a) The carrier frequency b) the signal-to-noise ratio c) the signal-plus-noise to noise ratio d) The baseband frequency range
You have an FSK transmitter using a mark frequency of 500 kHz, a space frequency of 380 kHz, and sending 10 kbps. A) How much bandwidth do you need for your transmission? B) if you are to design the system with continuous phase shift keying in mind, what would be the value of the space frequency if the mark frequency remains the same?
5. The following data is available: fc= carrier frequency = 750kHz, Ac= maximum amplitude of the unmodulated carrier = 10V fm= modulator frequency = 300Hz-8kHz modulation index m=0.5 a) What is the frequency of the upper sideband? b) What is the frequency of the lower sideband? c) What is the amplitude of the modulating signal? d) What is the maximum amplitude of the envelope of the modulated signal? e) What is the minimum amplitude of the envelope of the modulated signal? f) What is the bandwidth of the modulated wave? g) Write an expression for the modulated wave
Use Carson’s rule to determine the bandwidth of an FM channel when the maximum deviation allowed is 5 kHz at frequencies up to 3.333 kHz. Sketch the spectrum, showing carrier and sideband values.