A milk sterilizer flow system accepts milk at 20°C, 100 kPa and uses steam at 1 MPa, 200°C to heat the milk to the boiling point (i.e., a saturated liquid). If you treat the milk as water, and the inlet milk flow rate is 10 kg/s, find the flow of the steam needed to accomplish the heating (kg/s). 2 Milk + 100 kPa Saturated Liquid Adiabatic Throttle 100 kPa 4 1 Steam 3 1 MPa 200°C Milk 100 kPa 20°C 10 kg/s

A milk sterilizer flow system accepts milk at 20°C, 100 kPa and uses steam at 1 MPa, 200°C to heat the milk to the boiling point (i.e., a saturated liquid). If you treat the milk as water, and the inlet milk flow rate is 10 kg/s, find the flow of the steam needed to accomplish the heating (kg/s). 2 Milk + 100 kPa Saturated Liquid Adiabatic Throttle 100 kPa 4 1 Steam 3 1 MPa 200°C Milk 100 kPa 20°C 10 kg/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hi! Super needed rn, pleaase help me!! A steam throttling valve with inlet conditions of 2MPa and 400C is connected to the inlet of the turbine. The turbine has 200kW power output and heat abstracted of 100kW. If the mass flow rate is 1kg/s and the exit temperature of steam is 300C, find the exit turbine pressure.
In a refrigerator the power rating impressed on the compressor is 1.2 kW. Thecirculating wire in evaporator is 5 kW and the cooling water took away 10 kW fromcondenser coil. The operating temperatures range is 18ºC and 0ºC and theircorresponding latent heats are 170 kJ/kg and 230 kJ/kg and the difference between theliquid energy is 35 kJ/kg. Find the actual COP of the system (2) relative COP, assumingthe vapour is just dry and saturated at the end of the compression.
The enthalpy entering the turbine of a geothermal power plant is 2750 KJ/kg and ,ass rate of 1 Kg/sec. The turbine brake power is 1000 KW condenser outlet has enthalpy of 210 KJ/kg. If temperature rise of cooling water in condenser is 8, what is the mass of cooling water requirement?
Steam turbine with 1.5kg / s mass flow, 6MPa pressure, 500C temperature and 20 m / s speed is entering. The pressure at the outlet is 0.5MPa, the speed is 75 m / s and the degree of dryness is 0.95. Turbine power If its output is 2500kW, calculate the heat transfer from the turbine per unit time.
The compressor used in a refrigeration cycle takes in saturated R-134a vapor at a pressure of 360 kPa and raises it to a pressure of 1.0 MPa. The compressor can be considered well-insulated and inlet and exit velocities are small. In steady-state operation, the mass flow is 0.048 kg/sec and the power requirement is 1450 Watts. Find the discharge temperature.
A flashed-steam geothermal power plant is located where underground hot water is available as saturated liquid at 600 kPa. The flashed steam enters a turbine at 529 kPa, 98 % quality and expands to 15 kPa, when it is condensed. The flow rate from the well is 28.9kg/s. Over-all efficiency is 90%. Determine the power produced by the plant in KW.
A condenser takes in steam with enthalpy of 2450 kJ/kg and mass flowrate of 2 kg/s. It also discharges water at 20 kPa. What is the rate of heat removal of this system?
Steam enters the high-pressure turbine at 150bar and 550c and low pressure turbine at 40bar and 550c .the condensor pressure is 0.1bar using mollier diagram find 1.the dryness fraction at the end of low pressure turbine 2.efficieny 3.steam rate 4.heat rate 5.work ratio
A compressor brings R-134a from 150 kPa, -10 degree Celsius to 1200 kPa, 50 degree Celsius. It is water cooled, with heat loss estimated as 40 kW, and the shaft work input is measured to be 150 kW. What is the mass flow rate through the compressor?
A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so that the outlet is at 45 °C, then reheats at 500 kPa up to 400 °C, then takes perform a low pressure expansion in the turbine. Determine: net power output
A flashed-steam geothermal power plant is located where underground hot water is available as saturated liquid at 620 kPa. The flashed steam enters a turbine at 530 kPa, 98 % quality and expands to 15 kPa, when it is condensed. The flow rate from the well is 27.8 kg/s. Over-all efficiency is 90%. Determine the power produced by the plant in KW.
Answer the folloeing problems: A two-stage compressor takes air at 100kpa and 25C with volume flow of 0.123m3/s and discharges to 800kpa. What is the heat rejected(kw) by the intercooler? ANS. 14.82 A two-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and discharges it at 7500kpa. Find the heat rejected(kw) at the intercooler. ANS. 27.015