A motor is mounted on a platform that is observed to vibrate excessively at an operating speed of 6000 rpm, producing a 250 N force. Design a vibration absorber (undamped) to add to the platform such that the displacement of the motor becomes zeo. Note that in this case, the absorber mass will only be allowed to move 2 mm because of geometric and size constraints.

A motor is mounted on a platform that is observed to vibrate excessively at an operating speed of 6000 rpm, producing a 250 N force. Design a vibration absorber (undamped) to add to the platform such that the displacement of the motor becomes zeo. Note that in this case, the absorber mass will only be allowed to move 2 mm because of geometric and size constraints.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Explain why a constant force on the vibrating mass has no effect on the steady-state vibration.
Given a SDOF of spring-mass-coulomb damping, with mas of 0.1kg, stiffness of 10N s/m and a damping force of 0.1N is excited by a harmonic force of 1N amplitude at 1hz. Assuming steady-state condition, calculate the amplitude of vibrationn of the mass. How long the vibration will continu if the excitation is removed?
A 0.600kg mass oscillates at the end of spring that has a spring constant of 300N/m. theinitial amplitude is 0.500m . the damping force is proportional to the velocity, -av. If theamplitude decreases from .50m to 350m in 2.50s . What is the damping constant ?Is thesystem underdamped, critically damped or overdamped?
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
Mechanical Vibration Question is image A 100-kg tumbler produces a harmonic force of magnitude 5000 N. The stiffness coefficient of the support is 10×10^4N/m and damping coefficient ζ=0.2 If the maximum deflection is to be less than 0.06m find the operating frequency range?
A washing machine with a mass of 60 kg and a drum radius of 15 cm, rotates at 1000 rpm and washes 3 kg of unbalanced laundry. a) How much dynamic force would be transmitted to the ground if no vibration isolation was taken from the machine?b) What would be the stiffness (k) of the visco-elastic floor if an insulation measure with a damping ratio of 0.1 was taken, which would reduce the force transmitted to the floor by 90%?
A 0.600kg mass oscillates at the end of spring that has a spring constant of 300N/m. the initial amplitude is 0.500m . the damping force is proportional to the velocity, -av. If the amplitude decreases from .50m to 350m in 2.50s . What is the damping constant ?Is the system underdamped, critically damped or overdamped?
A 0.20 m long shaf with negligible inertia has a flywheel suspended from the end and a damper to damp the vibrations. The shaft has a torsional stiffness of 5,000 N-m/rad and a modulus of rigidity of 152 Mpa. The flywheel has a moment of inertia of 30 kg-m2 and the damping ratio is 0.4. Calculate the following: a) The damped frequency (in Hz) b) The damping coefficient (in N-m-s) c) The actual angular frequency (in Hz) d) The amplitude reduction factor e) The diameter of the shaft (in mm)
Mechanical Vibrations Question is image A 300-kg machine is attached to an elastic foundation of stiffness 3.1 x E6 N/m and damping ratio 0.06. When excited by a frequency squared excitation at very large speeds, the machine's steady-state amplitude is 10 mm. What is the maximum steady-state amplitude the machine would experience at lower speeds?
A reciprocating machine weighing 100kN is known to develop vertically oriented harmonic forces having and amplitude of 2.5kN at its operating speed of 40Hz. In order to limit the vibrations excited in the building in which the machine is installed, it is to be supported by a spring at each corner of its rectangular base. The designer wants to know what support spring stiffness would be required to limit to 0.4kN, the total harmonic force transmitted from the machine to the building.
Please show all work. will upvote, thanks An input force f = F‧sin(ωt) is applied to the body in both systems along the direction x. -Which of the two systems performs better in the frequency domain in terms of reducing the steady-state displacement amplitude X of the body ? Known are: m = 1kg, c = 5 Ns/m and k = 100 N/m?
An engine valve assembly depicted is figure; where k = 857.8 N/m; c =7.8 kg/s, and m =0.0492 kg, calculate the natural frequency and damped frequency in rad/sec and Hz. What critical damping value, damping ratio and what damping case is this system? *