Take into account the shown member when a ten kilonewtons load is applied to the centroid of its cross-section. Which of the following provides section a-a's normal stress to be maximum? 10kN |-0.25 - 40mm 20mm Section a a a.476.25 MPa b.1218.75 MPa c.1226.25 MPa d.468.75 MPa Fcomm T 40mm 1 TH 0.50m 0.50m

Take into account the shown member when a ten kilonewtons load is applied to the centroid of its cross-section. Which of the following provides section a-a's normal stress to be maximum? 10kN |-0.25 - 40mm 20mm Section a a a.476.25 MPa b.1218.75 MPa c.1226.25 MPa d.468.75 MPa Fcomm T 40mm 1 TH 0.50m 0.50m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Kindly give right answer other wise don't attempt Determine the maximum stress produced in a rectangular plate 50 mm wide, 8 mm thick with a central hole of 10 mm. It is loaded in an axial tension of 1 kN. Answer-7.813N/MM2
The uniform 3000??bar is supported by a smooth wall at A and by a pin at B. Determine (a)the diameter of the smallest pin that can be used if not to exceed a shear stress of 60???(Drawthe required FBD and answer in mm)(b) the bearing stress in thesupport bracket (Draw the required FBD and answer in MPa)(c) the bearing stress in the bar at B (Draw the required FBD and answer in MPa).
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
The structure shown has a diameter of 40??. The length dimensions are ? = 525 ?? and ? = 110 ??. Using load magnitudes of ? = 900 ? and ? = 1600 ?, determine the stress state at point H.
Help ASAP Determine the tensile stress in the upper plate at section b-b in mpa 3decimals
Help ASAP Determine the sheer stress at the base foundation in Mpa( 3 decimals)
Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it developed a stress of 52 MPa. Take note that the inner diameter is 2/6 of the outer diameter. hiii pls help urgenttt ty
The tube is 0.25 in. thick, is made of a 2014-T6 aluminum alloy, and is ixed at its bottom and pinned at its top. Determine the largest axial load that it can support.
The assembly consists of three disks A, B , and C that are used to support the load of P. The load P(kN) = 328 . The thickness of block B t1(mm)=26 . The thickness of block t2(mm)=13 . The allowable bearing stress ()b (MPa) = 213 . The allowable shear stress Tallow (MPa) = 71 =Bear area of disk A =Bear area of disk B
The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a length of 126 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 403 mm2. Ealuminum = 70 GPa. The correct answer is 887.66682. Show solution pls.
A 2 m hollow cast iron pole has an outside diameter of 250 mm and a thickness of 10 mm. The pole is subjected to an axial compressive force of 15 kN, determine the axial stress (kPa) of the pole due to compression. Neglect weight of pole.
Determine the factor of safety as per tresca's max shear stress theory