A moving point disturbance travels at a supersonic speed. It creates two spheres one at time (t) and the next one after (8t) time interval, 36 m ahead. Assuming the medium to be standard sea level atmosphere with 20°C, calculate the Mach number and velocity of the object and the Mach angle of the cone created by the disturbance. It 2=3m 36m R=12m t+ St I

A moving point disturbance travels at a supersonic speed. It creates two spheres one at time (t) and the next one after (8t) time interval, 36 m ahead. Assuming the medium to be standard sea level atmosphere with 20°C, calculate the Mach number and velocity of the object and the Mach angle of the cone created by the disturbance. It 2=3m 36m R=12m t+ St I

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.24P: Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the...

See similar textbooks

Similar questions

An aircraft with a cruising speed of 750 km / h, at an altitude of about 11500 m.is progressing. The aircraft has a top view area of 160 m2 and a total mass of 80000 kg.given. Also, the air density at this altitude is about 0.3 kg/ms. airplane landingand uses double-slit wings for take off. However, while cruisingIt continues its flight by collecting its wings. NACA 23012 airfoilown aircraft;a) at the time of take-off and landing when the wings are extended and not extendedFind the safe lowest speeds required.b) determine the angle of attack required for continuous cruise at cruise altitude.c) the strength to provide the necessary thrust to overcome the resistance force coming upon it.calculate.(Air density on the ground is determined as 1.20 kg/m3.
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 1-cm-diameter cups with a center-to-center distance of 22 cm, as shown in Fig. 1. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 20 m/s and air density of 1.25kg/m3, determine the maximum torque this turbine applies on the pivot.
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 8-cm-diameter cups with a center-to-center distance of 40 cm, as shown. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 15 m/s and air density of 1.25 kg/m3 Using appropriate software, investigate the effect of wind speed on the torque applied on the pivot. Let the wind speed vary from 0 to 50 m/s in increments of 5 m/s. Tabulate and plot the results.
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 8-cm-diameter cups with a center-to-center distance of 40 cm, as shown. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 15 m/s and air density of 1.25 kg/m3, determine the maximum torque this turbine applies on the pivot.
Joe can pedal his bike at 10 m/s on a straight levelroad with no wind. The rolling resistance of his bike is0.80 N ? s/m—that is, 0.80 N of force per m/s of speed.The drag area (CDA) of Joe and his bike is 0.422 m2.Joe’s mass is 80 kg and that of the bike is 15 kg. He nowencounters a headwind of 5.0 m/s. (a) Develop an equationfor the speed at which Joe can pedal into the wind. Hint:A cubic equation for V will result. (b) Solve for V; thatis, how fast can Joe ride into the headwind? (c) Why isthe result not simply 10 -5.0 = 5.0 m/s, as one mightfi rst suspect?
A wheel tractor has a 200HP engine.If the weight of the wheel tractor is 30 tons and the weight on the drivingwheels is 50% of this weight, and it is operating at an altitute of 1000m above sea level, at an average temperature of 25 degree celcius, and at an average speed of 12km/hr. What is the maximum available rimpull if thecoefficient of traction is 0.25?. Take rimpull efficiency as 85%
The boundary layer formed as turbulent around the sphere is when ReD = 2.5*10^5 (a) Golf ball(D=43mm) (b)Soccer ball(D=222mm) How fast does the ball have to be in order for a turbulent boundary layer to form around a ball? Assume standard atmospheric pressure.
A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water ( ρ = 1000 kg/m3 and ν=1.31 * 10 -6 m2 / s ) in the direction of its length at a speed of ( 20 cm / s ). Determine; a) The skin frictional drag force on both sides of the plate. b) The boundary layer thickness at the end of the plate.
For flow over a smooth plate, what approximately is the maximum length of the boundary layer if V_o = 9.0 m/s in the irrational uniform flow and the fluid is air? Water?
An 16-kg slab slides down a 25° inclined plane on a 4-mmthick film of SAE 30 oil at 15.6 °C; the contact area is0.3m2. Find the terminal velocity of the slab. Explain ur answer
What is the equation for the time of flight of a projectile? Is this equation dimensionally homogeneous?
Explain boundary layer thickness?