Answered: A new cast iron pipe must carry 1.2…

A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using n= 0.019 Choices: A. 1210.47 B. 1012.74 C. 2101.74 D.112.47

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q3/A) In Figure No. (4) the value of pressure of Confined Water pB at the center of pipe No. (2) is…

A: Finding out pressure at point A.

Q: Two tanks with a difference in water levels of 180 m are shown in Figure Q4. The tanks are connected…

Q: Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m…

A: Given :-Length between A and B = 5km = 5000m Diameter of pipe = 60 cm = 0.6 m point A is higher…

Q: A uniform body of size 4 m long x 2 m wide and 1 m deep floats in water. Determine the metacentric…

A: A uniform body with dimensions given and it has been asked to determine the metacentric height.

Q: Find the water speed at section 2 and pressure at section 3 and flow rate at section 4 for the…

A: Given data in question Branched pipe. 4 sections of pipe Area, discharge and pressure is given at…

Q: Question 2 Refer to Figure 2 below. If the water surface elevation in reservoir B is 110 m, what…

Q: Question 20 There are three pipes and each has different friction or roughness factors below: Saint…

Q: 3. A vertical storage tank with a hemispherical bottom and cylindrical shell of 4m internal diameter…

Q: A sump pump (used to drain water from the basement of houses built below the water table) is…

Q: A 1.25-cm diameter orifice in a vertical wall of a tank under a constant head of 5.50m discharges…

Q: 25. If the capillary rise of water in 1 mm diameter tube is 3 cm, the height of capillary rise of…

Q: Through the pipeline system in the figure calculate gauge and absulate presures at A and B J0. 12…

Q: Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 =…

A: Applying Bernoulli`s equation between point 1 and 2 in the given pipe flow:…

Q: If a steel rectangular gate of 1.2m wide by 1.75 m high, is located in the wall of a reservoir. It…

A: The question is based on the steel rectangular gate. The dimension of the gate, the density of…

Q: As part of a flow and pressure analySIs, a rectangular pipe loop with a length m and width of 300 m…

A: Equivalent pipe means a pipe which can replace existing compound pipe while carrying same discharge…

Q: Calculate the diameter of vertical pipe needed for flow of liquid at R = 1800 when the pressure…

A: Consider the given data

Q: Q2) Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

Q: There is a leak in a horizontal 30 cm pipeline (f= 0.025). Upstream from the leak two gages 600 m…

Q: The elasticity and dimension of a pipe are such that the celerity of pressure wave is 975 m/s. The…

A: Given data in question Celerity Discharge Diameter Change in Discharge To find out Water hammer…

Q: A horizontal 7.5 cm diameter sharp-edged orifice with Cc = 0.063 and Cv= 0.98 is under a head of…

A: Given: The diameter of the orifice is 7.5 cm. The value of Cc is 0.063. The value of Cv is 0.98. The…

Q: Water is flowing through a tube with the constant surface area as shown in the Figure Q2. 150 kPa 2…

A: Friction factor = 0.025 Velocity = 1.5 m/sec Viscosity of water ,μ = 8.9 x 10-4 Pa.s Length of flow…

Q: The pipe flow in the following figure is driven by pressurized air in the tank. The flow rate in the…

A: Find velocityQ=503600m3sec=0.01388m3secv=QA=0.01388m3secπ40.052=7.07355msApply Bernoullis theorem…

Q: A pressure gage at Elev.8.00m on the side of a tank containing a certain liquid reads 57.4kPa, while…

Q: Water (p =10 kg/m³) flows through the shown horizontal pipeline. At section (1), the flow velocity…

A: ρ = 10Kgm3P1 = 5KPa = 509.8581Kgm2v1 = 6msArea of the pipes = a = .15m2 Patm = 1498.9829 Kgm2 v1 =…

Q: Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

Q: Length of Pipe 3 = 210 m Length of Pipe 4 = 450 m *Pipe 2 and Pipe 3 are parallel Diameter…

Q: 6.12 An excavation is made for a canal that is fed by a stream, as shown in Figure P6.12. The…

A: 6.12 The hydraulic conductivity is the measure the transferring capacity of water from one point to…

Q: Q1) Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

Q: 10.33 Water (10°C) flows through a 25 cm smooth pipe at a rate of 0.05 m³/s. What is the resistance…

A: Given , diameter of smooth pipe d=50cm Discharge(Q) = 0.05 m3/s Q = A V Where, A = Area of flow…

Q: 3) Water is moving with a velocity of 5.0 m/s through a pipe with a cross-sectional area of 4.0 cm?.…

Q: A tank is in the shape of a frustum of a pyramid having a square section. The upper base is 3.0m x…

Q: 5. A circular pipe of radius 7 cm is used for water flow transmission. This pipe is moulded into…

A: Given data- Radius of circular pipe (R) = 7cm Pipe is moulded in sqaure ,where keeping the length…

Q: 3. A tank to form a frustum of a right circular cone 1.50m in diameter at the bottom, 3m diameter at…

A: Given data, C= 0.62 H2 = 0 H1 = 3.5m Time = 8 min To find out dia of orifice.

Q: Try making the flow net for the following diagram. Given: H1= 6m H2= 1.5 m D= 8m D1= 4m Draw a flow…

Q: In the figure shown, Zp = 4 m, length of pipe from the reservoir to the pump is 120 m, from the pump…

A: Given, f = 0.02 LAB = 120 m LCD = 1000 m

Q: 3. A rectangular gate 1.4 m in base and 1.8 m high is placed on the face of the water reservoir, as…

A: Solution; Given Data; Rectangular Gate; b=1.4 m h=1.8 m m=20 kg D=2 m mgate=50 kg H=4 m

Q: A rectangular tank 3 m x 4 m is 5 m high with 2 orifices placed at a vertical distances of 0.5 m and…

Q: Water flows in a 350mm- diameter pipe at the rate of 600 liters per second. The pipe has a length of…

A: Given: The diameter of the pipe is 350 mm. The flow rate is 600 l/sec. The length of the pipe is 64…

Q: Calculate the pressure due to column of 0.4 m of mercury(s=13.6). Take density of water = 1000…

Q: A 1.5m square tank, 3m tall is drained by a 25mm-diameter orifice located at its bottom. If the tank…

A: Time(t) =45min Initial head H1=3m To find final head H2

Q: Water flows on a straight 350 m non-rigid pipe, 600 mm in diameter. The velocity of flow is 2.3 m/s.…

A: i have used here the simple formula directly to calculate celerity of pressure wave okay

Q: A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower…

A: P1=68.07kPa D1=0.6m D2=1.2m Q=5400 lit/sec

Q: Question 2: A pipeline carries a pumped flow of 0.05 m/s. The line contains three 90 degree bends…

A: Given, Flow rate (Q) = 0.05 m3/s Length (L) = 300 m

Q: Water (p =1000 kg/m , p=1.59×103 kg /m.s) is flowing with the velocity of 0.25 m/s through a smooth…

A: i. The diameter of pipe is 1 cm = 0.01 m initially and then changed to 1 m. So it is the case of…

Q: A rough pipe of 0.5 m diameter, 300 m length and roughness height of 0.25 mm, carries water…

A: Given data, kinematic viscosity = γ = 0.9 × 10-6 m2/sec, length l = 300 m velocity = 3m /sec…

Q: The tank shown is 8 m long and has cross sections that are isosceles triangles with base (on top) 3m…

Q: The figure below shows a looping pipe system. Pressure heads at point A and E are 70 m and 46 m…

Q: An open circular vessel is 1m in diameter and 2m height. It contains water filled to a depth of…

Question

A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using n= 0.019 Choices: A. 1210.47 B. 1012.74 C. 2101.74 D.112.47

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A rectangular channel 1 m wide, Chézy C = 60, S = 0.0064, carries 1 m/s. Determine the velocity.
1. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.) 39.5136 b.) 12. 9517 c.) 99.9358 d.) 30. 4889 2. What gage pressure p1 in kPa, is needed to provide the given flow rate? a.) 1121kPa b.) 1328kPa c.) 1692kPa d.) 1725kPa
A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using f = 0.02 Choices: A. 681.95 B. 168.59 C. 961.85 D. 861. 95
Fluid Mechanics Motor oil (SAE 10W-30) flows between two parallel plates 6cm apart (B=6cm) at 38oC under a pressure gradient dp/dx of -1.5kN/m3 with a velocity distribution as shown by the blue curve in the picture, and given by: u(y)=-1/2mu dp/dx (By-y2) What are the velocity and shear stress at the wall; a distance of 10 mm from the wall?
Determine the rate of flow in the channel of Prob. 14.84, knowing that b= 12 ft, d1 = 4 ft, and d2 = 5 ft.Reference to Problem 14.84:The depth of water flowing in a rectangular channel of width b at a speed v1 and a depth d1 increases to a depth d2 at a hydraulic jump. Express the rate of flow Q in terms of b, d1, and d2.
Water flows in a wide channel at q = 20 m2/s and y1 = 2.75 m. If the flow undergoes a hydraulic jump, calculate: Fr1
Q7) A flow of 2 cumecs in a channel 2m wide has a uniform depth of 1m. Find the change in water surface elevation due to a contraction in width to 1.25m, and a smooth downward step in the bed of 50mm.
A rectangular channel 3.7m wide conveys7.4m3/s of water at a depth of 300mm.If a hydraulic jump occurs at a point ;find the increase in water level after jump
1. A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using f=0.029 Group of answer choices 928.44 428.94 284.94 892.44
6. Determine the magnitude of the resultant R, if P2 = 978, P3 = 780.
If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.
1. A 3.1 – m wide rectangular flume carries water at 5.60 m3/s. The bed slope is 0.00078 and n = 0.010. At a certain section, the depth is 92 cm. a. How far therefrom is the depth 80 cm? b. What is the slope of the egl? c. What is the headloss? 2. A rectangular channel 1.8 m wide conveys water at a depth of 1.2 m. a. What is the velocity of flow if it is laid on a slope of 0.002 and n= 0.012? b. What is the discharge if the channel slopes 0.1° and n = 0.016? Use Kutter’s formula for C. c. What is the velocity of flow if S = 0.000263 and f = 0.02?