A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a force of F = 5kN. Find the minimum factor of safety using Maximum shear stress theory. All dimensions are in mm. 500 25 D.- 20- 20 -35 D. 180- -3 R. 280- -175- -50 D. -25 D. -20 -20

Q: What are the principal stresses? How can they be determined?

A: Principle stresses can be defined as the maximum or minimum normal stresses on a specific plane. The…

Q: What are the general equations of plane stress transformation?

A:

Q: The image shows the yield loci for the Tresca and von Mises yield criteria. Between which two points…

A: GIVEN: TO FIND:

Q: 2.20. The uniaxial yield strength of annealed AISI 1015 steel is 386 MPa. Estimate the shear stress…

A: Given data: It is required to determine the shear stress according to the Tresca’s theory and…

Q: Strain hardening is associated with hot working process. Select one: True False

A:

Q: How can we apply the general equations of plane stress transformation?

A: An object is under a biaxial state of stress when the stress exists only inside the 2-dimensional…

Q: The critical resolved shear stress for a metal is 33 MPa. Determine the minimum stress necessary to…

A: Given Data

Q: Uniform and non uniform stress, gives proper solution explanation with diagrams.

A: Given data Uniform and non uniform stress, gives proper solution explanation with diagrams.

Q: Consider the same circular plate, as in the previous question, and consider a plate thickness of…

A:

Q: Explain the principle of stress and

A: Principal stresses are maximum and minimum value of normal stresses on a plane (when rotated through…

Q: 3. Explain the concept and the relationship between state of stress at a point and transformation of…

A:

Q: Identify the indirect force in the following Select one: O Tensile O Both Tensile and Compressive O…

A: Solution:

Q: How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?

A: Answer: Maximum allowable shear stress for thick walled cylinders: As, we know that from maximum…

Q: What is G-P zone? Draw yield stress vs. aging time, use a simple sketch and explain the mechanism.…

A: G-P Zone

Q: Q3: Assume that Young's modulus for bone is 1.5 x 1010 N/m² and that a bone will fracture if more…

A:

Q: The more severe the change in geometry, the larger the stress concentration. Is it true or false?…

A: Stress concentration is a location in a member under load where the magnitude of stress is…

Q: Explain the deconvolution of the principal stress state into the hydrostatic and deviatoric stress…

A:

Q: What would happen to the wire if it were stretched beyond its elastic limit? What would happen to…

A: Consider the diagram of stress vs strain for tension test for a typical tensile metal as shown…

Q: A socket of above knee amputee is used in the following analysis. It may considered as cylinder with…

A:

Q: What is Shear Stress and explain with example?

A:

Q: the shear yield stress

A: Given; The uniaxial yield stress of a material is=300 MPa Acc. to Von Mises criterion,  Determine…

Q: One of the applications related to strain energy is Bow and arrow Explain how this is related to the…

A: Strain energy is the energy stored in a member due to deformation. It is the energy absorbed by a…

Q: Discuss the engineering applications of thermal stresses.

A: Thermal stress: The stress induced in any object due to the change in its temperature is known as…

Q: Derive and Express the relation of strain transformation in detail.

A: Given A body under 3D loading To find Strain transformation explanation

Q: CApans the temperature increase it would that number from the temperature er this contact and…

A:

Q: Part-A (Theoretical & Mathematical Problem) For the following state of stress, (a) using the general…

A: (a) Write the given stresses from the diagram.   σx=20 ksiσy=-10 ksiτxy=-12 ksi   Write the angle…

Q: With a suitable example explain the difference between True stress-strain and Engineering…

A:

Q: Using Mohr's circle (no credits otherwise), solve the following questions: (a) the principal…

A: Do the following steps in order to draw the Mohr's circle for the given state of stress. 1. Draw two…

Q: 3. A 30-cm long, 12-mm diameter carbon steel rod was subjected to 15,5 kN of tension. Calculate (a)…

A:

Q: 1 A rod of a certain material is 50 mm in diameter for the first 100 mm and 25 mm in diameter for…

A: Given data:Rod 1:Diameter, D1 = 50 mm = 0.05 m for first 100 mm lengthL1 = 100 mm = 0.1 mDiameter,…

Q: A 3D solid component is subject to external forces such that following three principal stresses are…

A:

Q: How is parabolic shear-stress distribution and Linear normal stress distribution created?

A: The parabolic shear stress distribution is mainly observed in transverse shear stress cases.…

Q: 1) How much stress will be generated in the 13mm diameter aluminum rod below with an increase in…

A:

Q: Define plane stress and plane strain, making clear which, if any, of the stresses are zero in each…

A: Plane stress If a plane is undergoing load and at any point, the normal stress vector is zero (the…

Q: clearly explain the terms linear strain and shear strain,what do they measure,how are they different…

A: Linear strain occurs due to normal force and shear strain occurs due to tangential force.

Q: From the consideration of the stress element, the shear stresses at x-plane and y-plane must be: of…

A: There is a stress element which is in the equilibrium condition. so all the net external forces and…

Q: :) Consider a homogeneous structure made out of metal subjected to homogeneous oundary conditions t…

A: The yield stress for a material subjected to different stress states can be determined using…

Q: (d) The yield strength values of pure aluminium (Al) and pure copper (Cu) are 25 MPa and 20 MPa,…

A: Solution: Given Data: σy,Al=25 MPaσy,Cu=20 MPaσy,AMM=200 MPaσy,CB=105 MPad=18.4 mm

Q: Q5) material given the data from a tension test ? How would you determine the strain- hardening…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.