A pair of helical gears mounted on parallel shafts have P,=6, 20, and b-4 in. The 32-tooth pinion and 48-tooth gear are made of steel having 400 Bhn and 350 Bhn, respectively. Manufacturing precision corresponds to curve C of Velocity factor chart. Use a mounting factor of 1.6. Center distance is 7.5 in. 1. What helix angle is required? 2. Estimate the horsepower that can be transmitted for 10 pinion revolutions with 99% reliability and a safety factor of 1.5 if the driving motor rotates 1200 rpm and involtes light shock and the driven load involves medium shock. Check for bending fatigue only.

A pair of helical gears mounted on parallel shafts have P,=6, 20, and b-4 in. The 32-tooth pinion and 48-tooth gear are made of steel having 400 Bhn and 350 Bhn, respectively. Manufacturing precision corresponds to curve C of Velocity factor chart. Use a mounting factor of 1.6. Center distance is 7.5 in. 1. What helix angle is required? 2. Estimate the horsepower that can be transmitted for 10 pinion revolutions with 99% reliability and a safety factor of 1.5 if the driving motor rotates 1200 rpm and involtes light shock and the driven load involves medium shock. Check for bending fatigue only.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
(b)A pair of straight bevel gears has a velocity ratio of 2:1. The pitch circle diameter of the pinion is 80 mm at the large end of the tooth.A5KW power is supplied to the pinion which rotates at 800 rp.m. The face width is 40 mm and the pressure angle is 20. Calculate the tangential ,radial and axial components of the resultant tooth force acting on the pinion
A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic load
Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotating at 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40 and 655M13, respectively. Use table 6.10 on page 128 to select the suitable gear and pinion. If the pinion has 20 teeth, use the Lewis formula to determine the face width of thepinion and gear. Then, do one set of calculations and tabulate the answers.
A pair of 20 pressure angle bevel gears of N , = 30 and N2 = 60 has a module m of 8.5 mm at the outside diameter . Determine the power capacity of the pair , using the Lewis and Buckingham equations . The gears have face width of 70 mm , K , = 1.5 , and the pinion rotates at 720 rpm . The gears are made of steel SAE 1040 and hardened to about 200 Bhn Hi sir this design machine
Design a pair of plastic gears to drive a small band saw, using the following data: The input is from a 0.5hp electric motor rotating at 1160 rpm. The pinion is mounted on its 0.75 in diameter shaft. The gear is rotating at 250 rpm. For design purposes, consider taking Np=18 (number teeth in pinion) and Pd = 12 (diametral pitch). In this case, the acceptable number of teeth in the gear should be: NG=58 teeth NG = 93 teeth NG = 84 teeth NG = 70 teeth
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
A 17-tooth 20° pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth disk gear. The diametral pitch is 10 teeth/in, the face width 1.5 in, and the quality standard is No. 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion is a grade 1 steel with a hardness of 240 Brinell tooth surface and through-hardened core. The gear is steel, through-hardened also, grade 1 material, with a Brinell hardness of 200, tooth surface and core. Poisson's ratio is 0.30, Jp = 0.30, JG = 0.40, and Young's modulus is 30(10°) psi. The loading is smooth because of motor and load. Assume a pinion life of 108 cycles and a reliability of 0.90, and use YN = 1.3558N-0.0178, ZN = 1.4488N-0.023. The tooth profile is uncrowned. This is a commercial enclosed gear unit. (a) Find the factor of safety of the gears in bending. (b) Find the factor of safety of the gears in wear. (c) By examining the factors of safety, identify the threat to each gear and to the…
A 57-tooth spur gear is in mesh with a 23-tooth pinion. The gearset transmits 125 hp at 1000 pinion rpm. Size the spur gears for a bending failure safety factor of at least 2 assuming a steady torque, 25∘ pressure angle, full-depth teeth, Qν = 9, an AISI 4140 steel pinion, and a class 40 cast iron gear. Part A Find the appropriate standard diametral pitch for the gearset. Part B Find the minimum required face width of the gears needed to satisfy the safety requirements
For a pair of spur gears, one design decision is to specify the pressure angles. Please select the common values of pressure angle per textbook. 300 200 250