A pair of spur gears with 20° full-depth involute teeth, the pinion shaft is connected to a 10 kW, 1440 rpm motor. The speed reduction is 4:1 and width of the tooth is 50 mm. The factor of safety is 5 and load stress factor for steel used in wear strength equation is given by N/mm² K = 0.16 BHN 100

A pair of spur gears with 20° full-depth involute teeth, the pinion shaft is connected to a 10 kW, 1440 rpm motor. The speed reduction is 4:1 and width of the tooth is 50 mm. The factor of safety is 5 and load stress factor for steel used in wear strength equation is given by N/mm² K = 0.16 BHN 100

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut. A.Determine the diametral pitch, B. face width, C. and tooth numbers if the material is cast iron, class 25
A 15 kW and 1200 motor drives a compressor at 300 a pair of spur gears having . The center-to-center distance between the shafts is 400 . The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa . Assuming that the drive operates 8 to 10 hours per day under light conditions , find from the standpoint of strength Module , 2. Fare and 3. Number of teeth and pitch circle diameter of each gear 2. Check the gears thus designed from the consideration of Static tooth load or endurance strength of the tooth flexural endurance limil (sigma_{\epsilon}) may be taken as 400 MPa 3. Check the gears thus designed from the consideration of wear surface endurance limit ( sigma epsilon x ) may be taken 700 MPa b ^ pi ( 6.154 - 0512/pi; F_{N}
A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion with 15 teeth. The overall ratio of the gearbox is 6:1 and the gearbox is transmitting a power of 6000W. If the factor of safetv is to be reduced to an absolute minimum acceptable value and the gears are to be made from a material with a Yield stress of 540 MPa, what is the face width of the gears (in mm) Express your answer in the form 21.00 ie with two decimal place an no units
A pair of 20º full depth involute teeth bevel gears connect two shafts at right angles having velocity ratio 3 : 1. The gear is made of cast iron having allowable static stress as 70 MPa and the 20teeth pinion is of steel with allowable static stress as 100 MPa and 200BHN. The pinion works at 750 r.p.m. Determine the maximum power can be transmitted by the gears if the module is 10mm. Kf=1.4
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
A 57-tooth spur gear is in mesh with a 23-tooth pinion. The gearset transmits 125 hp at 1000 pinion rpm. Size the spur gears for a bending failure safety factor of at least 2 assuming a steady torque, 25∘ pressure angle, full-depth teeth, Qν = 9, an AISI 4140 steel pinion, and a class 40 cast iron gear. Part A Find the appropriate standard diametral pitch for the gearset. Part B Find the minimum required face width of the gears needed to satisfy the safety requirements
A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa
A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MP
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotatingat 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40and 655M13, respectively State the design specification considering the following design factors:1. Functionality2. Stress
The gears of a gear wheel with a module of 4 mm, width of 60 mm and number of 18 teeth were broken during operation. If the gear wheel is made of cast iron (GG-25), with what torque is it loaded? Given: Speed factor Kv= 1.25; ku
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
A pair of straight teeth spur gear is to transmit 20kw when the pinion at 300rpm.the velocity ratio is 1:3.the allowable static stresses for the pinion and the gear material are 12MPa and 100MPa respectively.the service factor is 1.the pinion has 15 teeth and it's face width is 14 times the module.from the standpoint of strength only and taking into consideration the effect of the dynamic loading Determine; (A) module (B) face width (C) pitch circle diameter for pinion (D) pitch circle diameter for gear Tooth form factor;y=0.153_0.912÷no.of teeth Velocity factor;Cv= 3÷3+v