A parallel-plate capacitor has plates measuring 10 cm x 10 cm, spaced 1 mm apart. The dielectric is mica with a relative permittivity of 5.0, and the permittivity of air is 8.85 x 10-12 F/m. Which of the following choices is closest to the actual capacitance value? O 5 pF O 500 pF O 50 pF O 5000 pF

A parallel-plate capacitor has plates measuring 10 cm x 10 cm, spaced 1 mm apart. The dielectric is mica with a relative permittivity of 5.0, and the permittivity of air is 8.85 x 10-12 F/m. Which of the following choices is closest to the actual capacitance value? O 5 pF O 500 pF O 50 pF O 5000 pF

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Related questions

Q: An AM waveform has a maximum span of 7.5V while minimum span of 2.5V. Determine the modulation index…

A: We need to find out modulation index and efficiency for amplitude modulation.

Q: Calculate the input impedance for voltage series feedback when the amplifier has R₁ = 13 k2, the…

Q: the nonzantal usp Let's consider a rod subjected to the shown axial forces. If we consider a linear…

A: The Given Data is FB=20KN, δA=0.01209mm For steel, EAB=ECD=200GP9 For aluminum,EBC=70GP9 DAB=40mm,…

Q: (a) A 400 mm length of conductor carrying a current of 25 A is situated at right-angles to a…

A: In this question we need to find a diameter of pole face

Q: 3. Sketch the root locus for the unity feedback system as shown in the figure below for the…

A: Given: For the unity feedback system as shown in the figure below for the following transfer…

Q: Q1) Using the mesh analysis, find the power dissipated by 4k2 and 6k2 resistors for the network in…

A: We need to find out the power for given circuit

Q: 3-phase medium overhead transmission line has an impedance of 48.7+j80.2 ohm per phase, and shunt…

Q: To convert a 2 mA meter with internal resistance of 120 ohm into an ammeter of range 0-200 mA, the…

A: Given: Meter resistance, Rm=120 Ω Meter current, Im=2 mA Measured current, I=200 mA

Q: Refer to the Figure below, calculate vo with load. Assume VGSQ = -2.2V. (VDD = 12V, RD=3.6kohms,…

Q: Q5. Explain the difference for the following paragraphs, answer five only A. Auto transformers and…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 7. Explain how the starting torque of an induction motor depends on resistance and reactance of the…

A: The objective is to determine the dependency of the torque on the impedance of circuit.

Q: 10. A substation delivers 693 kW, 3-phase power at 26.6kV and this power is stepped down to 2.3 kV…

A: The Power output of a open delta configuration is expressed as, P3ϕ open△ = 3.VpIp Where, P…

Q: Q/A- For the circuit below Bdc=200, RB-50K ohm, RC-330 ohm, VBB= 20 volt, Vcc= 30 Volt. Vcc RB www…

Q: Q2) Calculate the current through and the power dissipated in the 202 resistor for the network in…

Q: The more reliable standard industry signal is

A: In this question we will write about standard industry signal....

Q: Write the general voltage equation for a 250-Hz source whose peak voltage is 300 V.

A: In this question, We need to Write the general voltage equation If frequency f=250-Hz source peak…

Q: Let A = (3y - z)ax + 2xzay Wb/m in a certain region of free space. (a) Show that V.A = 0. (b) At…

A: We need to find out the divergence of A and magnetic field and current density.

Q: Q4: An angular displacement capacitance transducer use semicircular plated with 13 mm diameter…

Q: Find the rms value of the full wave rectified sine wave in figure shown below. Calculate the average…

A: We need to find out RMS Value and power for given waveform .

Q: 38+1 Given f (t) = L-¹ [3+43+(-3) ] if lim f (t) = 1, then the value of k is 10 3 O 20 4 O

A: We need to find out the value of k for given final value .

Q: Diode Model: 1N5817 R = 10k Vi= sine (05 100) Given the parameters above, simulate the given circuit…

A: The Given circuit is R=10kVi=sine0 5 100 To simulate the given circuit

Q: A copper coil, when connected to a 30-volt supply, initially takes a current of 3 A and has a mean…

Q: Consider the circuit shown in the figure below. Given that R₂/R₁ = 2 and R3/R₁ = 6, the current…

A: In this question we need to choose a correct option.

Q: 3. The transistor in the circuit shown below has a dc current gain of ß = 100. a. Determine the…

A: Given A bjt amplifier circuit and it's parameters.we need to determine the voltage gain,input and…

Q: 3. An ON-OFF temperature controller controls a room air conditioner. The bandwidth (OH) is set to 4,…

Q: Refer to the Figure below, calculate Av. Assume VGSQ = -2.2V. (VDD 12V, RD=4.1kohms, R$=0.9kohms,…

A: We need to find out the voltage gain for given circuit

Q: Choose the correct answer.

Q: 12.0 V 5.00 Ω ΜΕ Prob # 29, p. 349 |3.00 V | 18.0 V 14.00 Ω |2.00 Ω της --- 3.30 Ω - 31

Q: Solve for total resistance

A: In this question , we will find equivalent resistances across AB.....

Q: Solve for RC. 12 V Select one or more: a. 500 ohms Ob. 1050 ohms c. none d 2200 ohms 2 mA Re 07.6V…

A: Given circuit:

Q: Q6) Determine the current drawn from the source in the given circuit in Fig. 6. 10 Fig.6 19 V

Q: A 10 kW, 250 V, dc shunt motor with an armature resistance of 0.8 Ω and a field resistance of 275 Ω…

A: DC shunt motor is known as a wound DC motor it is a self excited DC motor the field winding is…

Q: A device that converts an electrical signal to a standard instrumentation signal is a…

A: In this question, We need to fill the blank. A device that converts an electrical signal to a…

Q: Calculate the gain for the JFET amplifier circuit shown below. Show the details of your work. Write…

A: JFET is nothing junction field effect transistor is a current controlled device having three…

Q: 7- Iron loss in the rotor of a 3-phase induction motor (a) Very low frequency of emf induced in the…

A: In this question, We need to choose the correct options Iron losses in the rotor of the 3 phase…

Q: 3. An ON-OFF temperature controller controls a room air conditioner. The bandwidth (OH) is set to 4,…

Q: Using only one ideal operational amplifier, 2 resistors, and a 3.3 nF capacitor, design apo ed obeto…

Q: Fourier Series

A: Delta Function- It is also known as the unit impulse function. It's value is equal to zero…

Q: Given: L = 4pH; C = 11.26nF; R=0.18842 IF = 455kHz RF RF Filter Amplifier Mixer IF Amplifier &…

A: For the above given question we need to calculate the value of resonance frequency, quality factor…

Q: Refer to the Figure below, calculate Z, if VDD = 9V, RG-1Mohms, Rs-2.1kohms, lpss=16mA, VGsQ = -3.2…

A: We need to find out the output impedance for given circuit

Q: A The bandwidth of TV video signal is 4.5 MHz if the signal is converted to PCM bit stream with $12…

A: We need to find out the data rate for given pcm signal .

Q: For the figure below shows a d.c. Two-source network; the branch currents I, and I₂ are as marked in…

A: Given: Consider the following circuit: To find: Write using Kirchhoff's laws, two independent…

Q: 1) A sample of silicon at room temperature and in thermal equilibrium is doped with acceptor atoms…

A: Note : According to the guidelines of the company we need to answer only first question if all the…

Q: Refer to the Figure below, calculate Z₁. Assume VGSQ = -2.2V. (VDD 12V, RD=3.6kohms, Rs=1.2kohms,…

A: For the above given common Gate amplifier circuit we need to calculate the value of input impedance…

Q: Determine the total resistance. 4k52 W 6 кл RT M 16 кл ≤8k₂

A: In this question we need to find a total equivalent resistance of the given circuit

Q: Example 34.34. The power input to a 500 V, 50-Hz, 6-pole, 3-phase induction motor running at 975 rpm…

A: Given Few parameters of thre phase induction motor.we need to determine the slip,rotor copper…

Q: Example 05:- An inductance comparison bridge is used to measure inductive impedance at a frequency…

A: In this question inductance comparison bridge is given at balance.....We have to find out equivalent…

Q: 3. Which of the following statements IS NOT CORRECT ? * for two motors with equal output power,…

A: Motor: It is an electromechanical device. this takes the electrical input and converts this power…

Q: In regards shunt DC motors, is the statement “The armature current is equal to the field current"…

A: Types of DC Motor DC shunt Motor DC series Motor Seperetely excited Motor Compound Motor....etc

Q: _______ is a type of capacitive sensor that has only one plate of the capacitor in its assembl

A: Capacitor is an electrical elements that have two metallic sheets separated by a distance d,…

Question

A parallel-plate capacitor has plates
measuring 10 cm x 10 cm, spaced 1 mm
apart. The dielectric is mica with a relative
permittivity of 5.0, and the permittivity of air
is 8.85 x 10-12 F/m. Which of the
following choices is closest to the actual
capacitance value?
0 5pF
O 500 pF
O 50 pF
O 5000 pF

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the capacitor, EC, is 104 V; and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. Find the missing values. ET ER78V EC104V IT IR IC Z20 R XC VA P VARSC PF C
Capacitive Circuits Fill in all the missing values. Refer to the formulas that follow. XC=12fCC=12fXCf=12CXc Capacitance XC Frequency 38 F 60 Hz 78.8 400 Hz 250 pF 4.5 k 234 F 10 kHZ 240 50 Hz 10 F 36.8 560 nF 2 MHz 15 k 60 Hz 75 nF 560 470 pF 200 kHz 6.8 k 400 Hz 34 F 450
Assume that the current flow through the resistor, IR, is 15 A; the current flow through the inductor, IL is 36 A; and the circuit has an apparent power of 10,803 VA. The frequency of the AC voltage is 60 Hz. ET ER EL IT IR15A IL36A Z R XL VA10,803 P VARSL PF L
A postage stamp capacitor has the following color marks starting at the upper-left dot: black, orange, orange, black, silver, and white. What are the capacitance value and tolerance of this capacitor?
Which of the following is the capacitance of two 20-microfarad running capacitors connected in parallel? 10 microfarad 20 microfarad 30 microfarad 40 microfarad
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
What frequency must be applied to a 33-mH inductor to produce an inductive reactance of 99.526 ?
DHA) A capacitor bushing forms arm ab of a Schering bridge and a standard capacitor of 500 pF capacitance and negligible loss, forms arm ad. Arm bc consists of a non-inductive resistance of 300 Q. When the bridge is balanced arm cd has a resistance of 72.6 2 in parallel with a capacitance 0.148 micro Farad. The supply frequency is 50 Hz. Calculate the capacitance and dielectric loss angle of capacitor. Derive the equations for balance and draw the phasor diagram under conditions of balance.
A 200 Ω resistor, 0.900 H inductor, and 6.00 µF capacitor are connected in series across a voltage source that has voltage amplitude 30.0 V and an angular frequency of 250 rad/s. (a) What are v, vR, vL, and vC at t = 20.0 ms? Compare vR + vL + vC to v at this instant. (b) What are VR, VL, and VC? Compare V to VR + VL + VC. Explain why these two quantities are not equal.
A series L–R–C circuit has a supply input of 5 volts. Given that inductance, L = 5 mH, resistance, R = 75ohm and capacitance, C = 0.2µF, determine (c) the frequency at which the p.d. across the capacitance is a maximum and (d) the value of the maximum voltage across the capacitor. answer: c) 4741 hz, d)10.85volts
17. Suppose we have a RC circuit with an alternating voltage V(t) = V_{m} * cos(5t) If the initial voltage is 4V and the resistor has a resistance of 8 ohm and the capacitor is of capacitance 2F then the charge for the circuit is?