gle Chromeopt.php?attempt=518520&cmid=102873&page=28My bookmarks v> ENGG1010-2020S2 > Assessments> Assignment 5 (5%)CalendarBadgesAll coursesA particle is moving with an initial velocity of v = 12 m/sec and a constant acceleration of 3.78 m/sec2 in thesame direction as the velocity. Determine the distance the particle has traveled when the velocity reaches 30m/sec. (Use the Kinematic of Particles equations).O a. 200 mO b. 100 mO c. 150 mO d. 50 mearchTOSHIBAF4F5F6F7F8F9F10F11F1224&7.9.Y !UP :て1ق

Answered: Image /qna-images/answer/b3abc855-db0f-47d3-94b7-5889b8ae1ff3.jpg

A particle is moving with an initial velocity of v = 12 m/sec and a constant acceleration of 3.78 m/Sec- same direction as the velocity. Determine the distance the particle has traveled when the velocity reaches 30 m/sec. (Use the Kinematic of Particles equations).

A particle is moving with an initial velocity of v = 12 m/sec and a constant acceleration of 3.78 m/Sec- same direction as the velocity. Determine the distance the particle has traveled when the velocity reaches 30 m/sec. (Use the Kinematic of Particles equations).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gun is on the same horizontal level as a target 484 meters away. A bullet is fired from the gun with a muzzle velocity of 154m/s. At what angle of elecation should the muzzle of the gun be set in order to ensure the bullet hits the target? Hint: You may use the formulas for the horixzontal x(t) and vertical y(t) displacement of the particle: x(t) = ucos(α)t, y(t) - usin(α)t - ½gt2 , g = 10m/sec2.
A particle is projected from a horizontal plane and has an initial speed of 50m/s at an angle of 30 degrees above the horizontal. For how long is the particle at least 20 m above the level of the plane? Hint: You may use the formulas for the horizontal x(t) and vertical y(t) displacement of the particle: x(t) = ucos(α)t, y(t) - usin(α)t - ½gt2 , g = 10m/sec2.
Check to see whether the simple linear combination of sine and cosine functions Ψ = Asin (kx) + Bcos(kx) satisfies the time-independent Schrödinger equation for a free particle (V 0).
Please answer the question: Irrotational flow mean s A) A fluid particle has angular deformation B) A fluid particle is translated C) Total anqular velocity of fluid particle is zero D) A fluid particle has inear deformation E) None of these answers
Assume that annual energy requirement of an industry is 20000 kWh . DETERMINE size of wind turbine that is required to be installed to meet the energy requirement . Following assumptions are taken into account for estimation Annual energy requirement - 20000 kWh Propeller type wind machine is used . Coefficient of performance -0.40 Wind speed at 15 meter height is 5 meter / sec ( if the turbine hub is placed at the height other than 15 meter , the wind speed should be estimated as shown in " vertical wind speed variation section Density of air - 1 kg / m Capacity factor -0.30
A tentative rule was given about tipping in Testing Experiment Table 8.4, where if a vertical line passing through the object's center of mass is within the object's area of support the object does not tip. According to the rule, the full box of crackers in the following experiment, which has a width of 13 cm and a height of 20 cm, was seen to tip at an angle of: θc=tan−1(13 cm/20 cm)=33∘θ According to the rule, at what angle will a box with the left half filled with crackers begin to tip? Assume the box is light-weight and that the contents remain in the configuration in
This is the equations I learnt so far and can apply to this W = FS cos θ W = FS Kinetic Energy (KE = ½ mv2) & PE = mgh Eff= Wo/W& Eff=FoD0/ FiDi & Eff=AMA/IMA Momentum(P = mv) m1u1 + m2u2 = m1v1 + m2v2 Impulse(J = Ft = m Δv) Friction (F = μN) Power=Work/Time= Force x Displacement /Time
Plz, solve both parts and show what have been asked in the problem parts. Problem. 7.13. A ship 180m long is to operate at a speed of 40km/h, what should be its speed in m/s to give the same froud number? What is the value of the froude number?
Pls answer asap I will give good ratings A jet of water flows from left to right and hits a splitter block, as shown in the figure. Some of the jet is diverted upwards and some of it downwards. The incoming jet has a velocity U1=U1=1.6 m/s and a cross-sectional area A1A1. The jet that is deflected upwards has a velocity U2=U2= 0.7 m/s, a cross-sectional area A2=A2= 11 cm22 and is at an angle θ2=θ2= 35oo with respect to the horizontal. The jet that is deflected downwards has a velocity U3=U3= 0.9 m/s, a cross-sectional area A3=A3=14 cm22 and is at an angle θ3=θ3= 25oo with respect to the horizontal. The density of water is ρ=ρ=1000 kg/m33.see diagram attached and answer - A-Find the cross-sectional area of the incoming jet (in cm22) B- Find the horizontal force on the block (in Newtons) (Note: remember to convert the area of the jets from cm22 to m22!) c)The vertical force on the block is found to be FyFy. What velocity of the incoming jet (i.e. what value of u1u1) would be needed to…
The Reynold's number of a sphere falling in air is 1E6. If the sphere's radius is 1ft, what is its velocity? Density of air is 0.00234 slug/ft³ and viscosity of air is 3.8E-7 lbf-sec/ft²A. 2.5 ft/sB. 5.1 ft/sC. 40.6 ft/sD. 81.2 ft/s
Alex have a hobby to swim at noon.My posture were like 190 cm (102 kg), even though Alex looklike a giant, his personal record was 57 s for 100 m of freestyleswimming. While he have training at lane 4, his friend watchinghim at the middle of lane 6. He is Patrick that remain silent whilewatching Alex swim. Even though Alex try so hard, Alex just have theexact time to his previous best record when Patrick watchinghim. Alex remember that it little bit warm at that noon with 302 Kof water temperature. Alex just wonder, how much shear stressthat Patrick felt when Alex swimming across him? Sketch the system You can assume any logical data you need.
objective: designing an experiment that will correctly mathematically predict the speed of a marble at the bottom of a CPO roller coaster. a) what would be the necessary materials and procedures? b) how would the normal force Fn be determined/calculated?