I need the answer quickly A particular area can be supplied either by hydro station or steam station. Thefollowing data is available :Capital cost / Running cost/ Interest and ReservekWhStationdepreciation capacity7%9%Q6kW2000 $0.04 $30 %HydroSteam0.06 $1300 $22 %At what load factor would the overall cost be the same in both cases ? Whatwould be the cost of generating 55 x 10° units at this load factor ?

Answered: Image /qna-images/answer/5b184594-bed5-4348-b9e7-da57d48041e5.jpg

A particular area can be supplied either by hydro station or steam station. The following data is available : Capital cost/ Running cost / Interest and Reserve kWh 0.04 S 0.06 S Station depreciation capacity kW 2000 $ 1300 $ 7% Hydro Steam 30 % 9% 22 % At what load factor would the overall cost be the same in both cases ? What would be the cost of generating 55 × 10° units at this load factor ?

A particular area can be supplied either by hydro station or steam station. The following data is available : Capital cost/ Running cost / Interest and Reserve kWh 0.04 S 0.06 S Station depreciation capacity kW 2000 $ 1300 $ 7% Hydro Steam 30 % 9% 22 % At what load factor would the overall cost be the same in both cases ? What would be the cost of generating 55 × 10° units at this load factor ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
For the circuit shown in Figure 2.24, compute the voltage across the load terminals.
3. What is power factor?
A base load station having a capacity of 18 MW and a standby station having a capacity of 20 MW shares a common load. Determine the annual load factors and plant capacity factors of two power stations from the following data:Annual standby station output = 7·35 × 10^6 kWhAnnual base load station output = 101·35 × 10^6 kWhPeak load on standby station = 12 MWHours of use by standby station/year = 2168 hours
hydro-electric generating plant is supplied from a reservoir of capacity 20000000m3 with a head of 200m. The hydraulic efficiency of the plant is 0.8 and the electric efficiency is 0.9. What is the total available energy?
Determine the symmetrical components of the three currents ?? = 10 ∠ 0A; ?? =100 ∠ 2500 A; and ?? = 10 ∠ 1100 A.
A) An equalizer is a jumper used to parallel the series field of two compound DC generators when the two generators are being run in parallel to share an electrical load. a) true b) false B) The ohmic value of an equalizer is not important as long as it is made out of copper. a) true b) false C) How is the efficiency usually expressed?a) in watts b) in kilowatt-hours c) in percentage d) none of the above
An industrial assembly hall is continuously lightedby one hundred 40-W mercury vapor lamps suppliedby a 120-V and 60-Hz source with a power factor of0.65. Due to the low power factor, a 25 percent penaltyis applied at billing. If the average price of 1 kWh is$0.01 and the capacitor’s average price is $50 permillifarad, compute after how many days of operationthe penalty billing covers the price of the power factorcorrection capacitor. (To avoid penalty, the powerfactor must be greater than 0.85.)
1. Incremental cost fuel cost is GHC per megawatt hour for two units in a plant are given by dF1dP1=0.1P1 + 20 dF2dP2=0.12P2 + 16 The minimum and maximum load on each unit is to be 20 MW and 125MW respectively. Determine the incremental fuel cost and the allocation loads between units for this minimum cost when loads are i) 100MW ii) 150MW . Assume both units are operating.
What is the max power delivered to the load? Need help.
A base load station having a capacity of 18 MW and a standby station having a capacity of 20 MW shares a common load. Determine the annual load factors and plant capacity factors of two power stations from the following data: Annual standby station output = 7·35 × 106 kWh Annual base load station output = 101·35 × 106 kWh Peak load on standby station = 12MW Hours of use by standby station/year = 2100+67 hours
• T or F, modify the wrong part if False, please underline twice your answer if True or False. At maximum efficiency, the amount power that a DC generator would deliver will always be at maximum.