A petrol engine produces 250 kW while using 1.014 kg of fuel per minute. The fuel has a lower heating value of 45000 kJ/kg, and the engine has bore of 100 mm and the stroke-to-bore ratio of 1.2. The clearance volume of the cylinder is 1.178×10° mm³. The friction power is found to be 10% of the power that engine produces. Sketch (your own) the simple neat and clean block diagram of the engine, clearly indicating the control volume and control surface, with all the given data displayed on it. For air take the value of y=1.4.

A petrol engine produces 250 kW while using 1.014 kg of fuel per minute. The fuel has a lower heating value of 45000 kJ/kg, and the engine has bore of 100 mm and the stroke-to-bore ratio of 1.2. The clearance volume of the cylinder is 1.178×10° mm³. The friction power is found to be 10% of the power that engine produces. Sketch (your own) the simple neat and clean block diagram of the engine, clearly indicating the control volume and control surface, with all the given data displayed on it. For air take the value of y=1.4.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.10P

See similar textbooks

Similar questions

Using bolts of the same material and cross-sectional area, two possible attachments for a cylinder head are shown. Compare the strain energy developed in each case, and then explain which design is better for resisting an axial shock or impact load
A 4-stroke, 12 square-cylinder piston rotary engine is required for the propulsion of an aircraft cruising at speed of 100 m/s, at an altitude where the ambient conditions are 240 K and 46.6 kPa. The following data can be used: Thrust required5 kN propeller efficiency0.85 Engine brake thermal efficiency 0.35 fuel air ratio0.04 Engine rpm4000 Volumetric efficiency0.871. Calculate the engine brake power, bsfc, displacement volume and cylinder dimensions. 2. Calculate the fuel required to cruise from Jeddah to Dammam (1370 km). kindly, solve all requireds by clear handwritten
Power is transmitted from the 1st shaft to the 2nd shaft with a Conical Friction coupling at 950 rpm. If the taper angle is alpha 25 degrees and the average diameter is 120 mm, how much power is produced with a pressing force of 5000 N (kW)
A nut which is connected to a lead screw is moved in a horizontal plane against a force of 100kN at a speed of 4mm/sec by electric motor powered screw. The following data is given Single start square thread screw Pitch of the screw = 6mm Outlet diameter of the screw = 40mm Co-efficient of friction of the screw thread = 0.15 Efficiency of the motor = 85% Determine the power required and efficiency of the screw
120hp electric motor with 1180rpm propel the 15,000lbs to 55mph using a series of gearbox’s/transmissions and consumer available automotive drivetrain parts? And what kind of output shaft diameter would be optimal?
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?
the power transmitted by a single plate clutch at a speed of 2000 rpm, if the outer and inner radii of Triction surfaces -are 150 mm and 100 mm respectively. The maximum intensity of pressure at any point of contact surface should-not exceed 0.8 x 105 N/m2. Take both sides of the plate as effective and coefficient of friction = 0.3. Assume uniCalculateform wear.
What are the important factors to take into consideration when solving problems related to friction (Dry or Coulomb friction)?
Please show a clear step-by-step solution. Thank you! What is the proportion of the alteration in length for Spring A to Spring B, supposing that both springs carry an equal amount of load? Springs A and B have the identical qualities, with the exception that Spring A has 12 times the number of turns as Spring B.
A four stroke 394 mm bore and 534 mm stroke single acting diesel engine with four cylinders is guaranteed to deliver 350 Hp at 300 rpm. The engine consumed 66.8 kg/hr of fuel with a heating value of 44 251 KJ/Kg. Calculate the indicated mean effective pressure in KPa if mechanical efficiency is 85%.
In a rolling mill, the rollers can exert a pressure of 219 MPa on the sheet being rolled. If the friction coefficient between the roller and the sheet metal is 0.35 and the flow stress of the steel being rolled is 120 MPa, what diameter rolls would reduce the thickness of 2mm thick sheet by 25% in a single pass?
The diameter of the pulley on the compressor shaft must not be greater than 1.2 metre while the centre distance between the pulleys is limited to 1.85 metre. A compressor, requiring 95000W is to run at about 500 r.p.m. The drive is by V- belts from an electric motor running at 1500 r.p.m. The belt speed should not exceed 1500 m/min. The coefficient of friction between the belt and the pulley is 0.3. Determine the number of V-belts required to transmit the power if each belt has a crosssectional area of 3 cm2, density 1100 kg/m3 and an allowable tensile stress of 3 MPa. The groove angle of the pulley is 50°. Calculate also the length required of each belt.