The Stroke of a gas engine which works on the constant volume cycle is 488 mm. The pressure at the beginning of the compression is 0.72 bar and at the end of compression is 13.65 bar. Assuming compression follows the law PV^1.36 = C, Calculate the clearance between the piston and cylinder cover at the end of compression in mm of length.

The Stroke of a gas engine which works on the constant volume cycle is 488 mm. The pressure at the beginning of the compression is 0.72 bar and at the end of compression is 13.65 bar. Assuming compression follows the law PV^1.36 = C, Calculate the clearance between the piston and cylinder cover at the end of compression in mm of length.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. For a given pump, the diameter, the gauge pressures at the inlet and outlet are −30 × 103 P a and 200 × 103 P a, respectively. If the flow rate is 0.1 m3/s, and the power required is 25 kW, find the efficiency. The intake and discharge are at the same height. 2. The impeller of a radial-flow turbine has an outer radius of 4 f t, turning at 200 rpm. The volume flow rate is 1000 ft3/s, and it discharges in the axial direction. Neglect all losses. If the tangential component of the velocity at the inlet is 5 f t/s, find: (a) The torque exerted on the impeller. (b) The power developed by the machine.
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of thestroke volume. At the beginning of compression stroke the pressure of air is 0.99 barWhen the piston has travelled 260 m from the begining of the compression stroke thedelivery valves open and delivers air at 4 bar. Find the value of "n", iif the compressionfollows the law PVn = CA. 1.37B. 1.39C. 1.28D. 126
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of the stroke volume. At the beginning of compression stroke the pressure of air is 0.99 bar. When the piston has travelled 260 mm from the begining of the compression stroke the delivery valves open and delivers air at 4 bar. Find the value of n, if the compression follows the law PVn = C.
2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria meningitides. The dimensions for the bioreactor are Dt 12.9 cm, ratio Di/Dt = 1/3 and N = 700 rpm. With the scale up factor of 2.24, determine the impeller tip speed (m/s) for the pilot scale bioreactor based on constant impeller tip speed and constant power consumption per volume. Predict which scale up method might give a higher concentration of P64K, if the demand of dissolved oxygen plays an important role.
If a double-acting air cylinder with a 40-mm diameter bore and 200-mm stroke operates at 7000 kPa gage and cycles at 30 cycles /min , how long will it take to consume 100m3 of free air? (Assume the rod diameter is negligible and there is no change in the temperature of the air.
The cylinder bore diameter of a double-acting reciprocating pump is 160 mm and its stroke is 340 mm. The pump runs at 53 rpm and lifts water through a height of 29 m. The delivery pipe is 22 m long and 100 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 10 liters/s. Assume the weight density of water is 9810 N/m3
A pump, for which the characteristic curve is shown below, is used to pump water from a canal into a dam. The pump is mounted 2.0 m above the water level. There is a 50 mm PVC pipe connected to the suction side of the pump, and a 40 mm PVC pipe connected to the discharge side. The total length of pipe on the suction side is 8 m, and there is a strainer (K = 20), a non-return valve, a 90° elbow and a fully open gate ball valve in the suction line. Another fully open gate valve, and two 90° elbows are mounted in the discharge line. The total length of the discharge line is 60 m, and the discharge pipe outlet is 4 m above the pump. You may assume a water temperature of 25 °C. Determine: (a) The flow rate through the system(b) The required fluid power(c) The efficiency of the pump(d) Whether the pump will cavitate or not.
A 3-bladed wind turbine with 250 kW generator has diameter of 50 m and tower height of 60 m. It is designed to have Cp of 0.25 at wind speed of 12 m/s when regulation starts. The cut-in and furling Speeds for the machine are 5 m/s and 20 m/s respectively. Mechanical and electrical efficiencies are 90 % and 95 %. By assuming the density of air as 1.225 kg/m3. Calculatea. What is power developed by the rotor at 12 m/s when regulation starts? b. If the tip-speed ratio at this wind speed is 4.2, then what is the rpm of the rotor? c. Calculate the actual torque developed. d. Calculate the maximum possible annual power output.
1.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system tool , to know that the engine is capable to support the hydraulic system if a pump delivers 110 liters per minute and the pressure is 227bar.2.If the area of A1 = 0.05 m˄2 and the area of A2 = 1.5 m˄2 , external input force F1 = 50 N, then the external output force F2 ?
The cylinder bore diameter of a single-acting reciprocating pump is 150 mm and its stroke is 310 mm. The pump runs at 56 rpm and lifts water through a height of 28 m. The delivery pipe is 23 m long and 102 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 4.3 liters/s. Assume the weight density of water is 9810 N/m3
An engine developing 40 brake HP must be cooled by a radiator through which water is pumped from the engine. Calculate the required rate of flow in gpm if the heat transferred from the engine to cooling water = 40 HP, water temperature in radiator top water is 200 F and at bottom water is 190 F. One gal of water weighs 8.34 lb.
The cylinder bore diameter of a double-acting reciprocating pump is 170 mm and its stroke is 370 mm. The pump runs at 55 rpm and lifts water through a height of 26 m. The delivery pipe is 23.5 m long and 113 mm in diameter. Find (i) the theoretical discharge in liters/s,(ii) the theoretical power required to run the pump in kW, (iii) the percentage of slip, and (iv) the coefficient of discharge., if the actual discharge is 13 liters/s. Assume the weight density of water is 9810 N/m3 (i)Theoretical discharge in liter/s (ii) the theoretical power required to run the pump in kW (iii) the percentage of slip (iv) the coefficient of discharge.