A physics professor stands at the centre of a frictionless turntable with arms outstretched and a 7.75 kg dumbbell in each hand as shown in the following figure. He is set rotating about the vertical axis at 1.65 revolution per second. Find his final angular velocity if he pulls the dumbbells into his stomach. His moment of inertia (without the dumbbells) is 4.3 kgm? with arms outstretched and 2.2 kgm? with his hands at his stomach. The dumbbells are 1.3 m from the axis initially and 0.2 m at the end. Dumbbell Dumbbell Professor (not a dumbbell) BEFORE AFTER Insert the final angular velocity in revolutions per second correct up to at least a third decimal place.

A physics professor stands at the centre of a frictionless turntable with arms outstretched and a 7.75 kg dumbbell in each hand as shown in the following figure. He is set rotating about the vertical axis at 1.65 revolution per second. Find his final angular velocity if he pulls the dumbbells into his stomach. His moment of inertia (without the dumbbells) is 4.3 kgm? with arms outstretched and 2.2 kgm? with his hands at his stomach. The dumbbells are 1.3 m from the axis initially and 0.2 m at the end. Dumbbell Dumbbell Professor (not a dumbbell) BEFORE AFTER Insert the final angular velocity in revolutions per second correct up to at least a third decimal place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
A solid cylinder (r= 4cm) goes down a ramp at a declination of 20°. The longitude of the ramp is 75 cm and 20 cm high. On average, the cylinder takes 1.25 s to go down the ramp. Without specifying the value of the mass determineWhat is the acceleration of the center of mass?What is the angular acceleration of the object?What is the moment of inertia of the object?What is the value of the radius of gyration?
A professor's office door is 0.99 m wide, 2.2 m high, 4.2 cm thick; has a mass of 27 kg, and pivots on frictionless hinges. A "door closer" is attached to door and the top of the door frame. When the door is open and at rest, the door closer exerts a torque of 5.6 N*m. What is the moment of inertia of the door? If you let go of the open door, what is its angular acceleration immediately afterward?
In the figure, a shaft rotating with constant angular velocity and connected to this shaft at a distance of r1=136 cm, r2=49 cm, r3=69 cm and r4=61 cm m1=3.3 kg, m2=1.6 kg, m3=8.9 The point masses of kg and m4=10 kg are seen. Find the position of the counterweight in degrees, with rd=90 cm. (θ1=63˚, θ2=138˚, θ3=260˚, θ4=234˚)
In the following figure, we have a disk that has a force of 9.0 N. applied. The diameter of the disk is 0.120 m and its mass is 50 kg. The moment of inertia of the disk is: a) 3.00 kg m2 b) 0.54 kg m2 c) 0.09 kg m2 d) None of the above
A flywheel is fitted to a multi cylinder engine, which runs at a mean speed of 360 r.p.m. If the speed varies from 6 % above the mean to 2 % below it and the fluctuation energy is 1200 kN-cm, If the radius of gyration is 20 cm, find (i) mass moment of inertia of the wheel and (ii) mass of flywheel. The mass moment of Inertia in Kgm2 is Mass of the flywheel in kg is
An object is formed by attaching a uniform, thin rod with a mass of mr = 6.86 kg and length L = 5.76 m to a uniform sphere with mass ms = 34.3 kg and radius R = 1.44 m. Note ms = 5mr and L = 4R. 1) What is the moment of inertia of the object about an axis at the left end of the rod? kg-m2 2) If the object is fixed at the left end of the rod, what is the angular acceleration if a force F = 463 N is exerted perpendicular to the rod at the center of the rod? rad/s2
The plate of a record player with a moment of inertia of 0:015 kg m2 rotates freely at 33 rpm. If you slowly drop a 180-gram vinyl disc with a 30:48 cm diameter on the board, what will be the new angular speed? (N.B. In real life, the turntable motor forces the speed to always remain 33 rpm. In this problem, we act as if the engine did not exist. )
The propeller on Don Karnage's airplane can be modeled as three identical thin rods of uniform density extending radially from the rotational axis of the propeller. To take off, the propeller must accelerate from rest to 633 rpm in 4 s. If the length and mass of each rod are 0.872 m and 3.11 kg, what must be the magnitude of torque in N*m) necessary to accelerate the propeller? Explain how you solved the problem involving something undergoing angular acceleration Be sure to state what your known and unknown quantities are, what concepts were applied, and what equations were used!
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
The inverse pendulum system given in the figure is freeDraw a diagram of the object and moveGet the equation (the mass of the pendulum m,moment of mass inertia is ? = (1/3)??2)
In the system in the figure, the total mass of two plates of the same thickness, made of the same material and connected to each other is 70 kg. What is the angular acceleration of the system? (A1=1 m, B1=0.6 m. A2=1.2 m, B2=0.4 m, M=50 Nm)