A pipe flowing water has a manometer attached, as shown in the figure. The local atmospheric pressure, Po, is 101.3 kPa and the gravitational acceleration is 9.81 m/s². The densities of the water (pw), oil (Pon), and mercury (pug) are 1000.0, 800.0 and 13,600 kg/m³, respectively. The heights of the liquid levels in the manometer system are indicated in the figure. What is the absolute pressure at the center of the water pipe, Pw, in kPa.

A pipe flowing water has a manometer attached, as shown in the figure. The local atmospheric pressure, Po, is 101.3 kPa and the gravitational acceleration is 9.81 m/s². The densities of the water (pw), oil (Pon), and mercury (pug) are 1000.0, 800.0 and 13,600 kg/m³, respectively. The heights of the liquid levels in the manometer system are indicated in the figure. What is the absolute pressure at the center of the water pipe, Pw, in kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water fl ows upward in a pipe slanted at 30 ° , as in Fig. .The mercury manometer reads h =12 cm. Both fl uidsare at 20° C. What is the pressure difference p 1 - p 2 inthe pipe?
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?
When a clean glass tube with a diameter of 2 mm is immersed in water at 20 ° C, how many mm will the capillary rise occur in the glass tube? For water at 20 ° C, surface tension is given as 0.073 N / m, density 1000 kg / m3, contact angle 0 ° C and gravitational acceleration 10 m / s2.
Using the data given in the schematic attached, find the difference of pressure PA and PB h1= 0.65m h2= 0.1m h3= 0.75m h4= 0.45m Density of fluid A is pA= 900kg/m3 Density of fluid B is pB= 1034kg/m3 Mercury density is pHg= 13600kg/m3 Oil density is poil= 700kg/m3 (In the given figure, the pipelines are parallel to each other and not necessarily at the same height.)
In a certain industrial process, oil of density ρ fl ows throughthe inclined pipe in Fig. C3.1. A U -tube manometer, withfl uid density ρ m , measures the pressure difference betweenpoints 1 and 2, as shown. The pipe fl ow is steady, so thatthe fl uids in the manometer are stationary. ( a ) Find ananalytic expression for p 1 - p 2 in terms of the systemparameters. ( b ) Discuss the conditions on h necessary forthere to be no fl ow in the pipe. ( c ) What about fl ow up,from 1 to 2? ( d ) What about fl ow down , from 2 to 1?
Fluid mechanics, I need solutions in 15 minutes please. MCQ/Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. A-Fx = 257.430 kN and Fy = 59.801 kN B-Fx = 164.018 KN and Fy = 37.229 KN C-Fx = 269.894 kN and Fy = 65.526 KN D-Fx = 98.182 kN and Fy = 20.002 KN E-Fx = 234.789 kN and Fy = 52.418 kN F-Fx = 187.005 kN and Fy = 42.182 KN G-Fx = 119.956 kN and Fy = 25.550 KN H-Fx = 141.327 kN and Fy = 31.171 KN I-Fx = 288.147 kN and Fy = 69.098 KN J-Fx = 213.112 kN and Fy = 47.903 KN
Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3 kPa are measured for P1, P2 and p3, respectively, what are the head loss between 1-3 in meters.
For the inverted manometer shown in the figure, all the fluid are at 20 0C. If PB - PA = 687 kPa, What must the height H be in cm. Take water density = 1000kg/m3 Mercury density = 13600kg/m3
The airfl ow underneath an air hockey puck is very complex,especially since the air jets from the air hockey tableimpinge on the underside of the puck at various points nonsymmetrically.A reasonable approximation is that at anygiven time, the gage pressure on the bottom of the puck ishalfway between zero (atmospheric pressure) and the stagnationpressure of the impinging jets. (Stagnation pressureis defined as p0 =1/2ρV2jet . ) ( a ) Find the jet velocity V jetrequired to support an air hockey puck of weight W anddiameter d . Give your answer in terms of W , d , and thedensity ρ of the air. ( b ) For W = 0.05 lbf and d = 2.5 in,estimate the required jet velocity in ft/s.
Sometimes manometer dimensions have a signifi canteffect. In Fig. containers ( a ) and ( b ) are cylindricaland conditions are such that p a = p b . Derive a formula forthe pressure difference p a - p b when the oil–water interfaceon the right rises a distance ∆ h< h , for ( a ) d << D and ( b ) d=0.15 D . What is the percentage change in the value of ∆ p ?
A pipe has a cross-sectional area of 16.5cm2 at point A, where the speed of the fluid (water) is 1.2 m/s and the pressure is 2.00 atm. The pipe ascends 3.00 m and narrows to 8.20 cm2 at point C. a) what's the speed of the fluid at point C. b) what's the absolute pressure at point C.
A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. a. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? b. After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? c. What will be the absolute pressure (P3) in the smaller pipe? d. What is the volume flow rate through the smaller pipe?