Answered: A pipe is subjected to a tension force…

A pipe is subjected to a tension force of P = 45 kN. The pipe outside diameter is 41 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 120 GPa. Determine the normal strain in the pipe.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Related questions

Q: Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8 in. long, and the…

Q: A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the…

A: (a) To Find : The normal strain in rod 1. Given : The length of rod 1 is L1=148 in The length of…

Q: A steel bar of 3 m long and 2500 mm2 in area hangs vertically, which is securely fixed on a collar…

A: Given Area, A = 2500 mm2 Load, P = 25 kN Length, L = 3 m E = 200 GPa Find…

Q: v) A delta strain gauge is attached to the member at point ‘X’ as highlighted in the figure. During…

A: The magnitude of strain at an angle is given by:εθ=εx+εy2+εx-εy2cos2θ+γxy2sin2θAt…

Q: 6. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L…

A: Given:P=8 KNL=400 mmν=0.35E=70 GPa

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are εx = 0.40…

Q: Rigid bar ABCD is supported by two bars. There is no strain in the vertical bars before load P is…

A: (a) To find: The normal strain in bar 1. Given: The dimensions are L1=1900 mm, L2=1425 mm, a=190 mm,…

Q: The stress strain diagram for polyester resin is given in the figure. If the rigid beam is supported…

Q: A rigid steel bar is supported by three circular rods as shown in Figure below. There is no strain…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 31300 ksi] bars (1) and (2) are…

Q: H.W.I A rigid steel bar ABC is pinned at B and supported by two rods at A and C. There is no strain…

Q: A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the…

Q: An air-filled rubber ball has a diameter of 6 in. If the air pressure within the ball is increased…

A: Given data :Initial diameter (di) = 6 inFinal diameter (df) = 7 in

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

Q: H.W.7 A rigid steel bar ABC is supported by three rods. There is no strain in the rods before load P…

Q: A rubber block is placed between two rigid walls where a load of P = 60 kN is applied on top as…

A: GivenP=-60kN compressive

Q: A thin polymer plate PQR is deformed such that corner Qis displaced downward 0.0625-in. to new…

Q: A rigid steel bar ABC is pinned at B and supported by two rods at A and C. There is no strain in the…

A: The change in the length of rods can be determined as,

Q: H.W.7A rigid steel bar ABC is supported by three rods. There is no strain in the rods before load P…

Q: The Strain along the length direction of the block subjected to 3 mutually perpendicular forces as…

A: Given , Px is positive , Py and Pz are negative

Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of…

Q: A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of…

Q: Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L =…

Q: hand written plz i'll upvote Shown in the figures (1) and (2) are trusses containing members that…

A: To choose: The correct option. Given: The modulus of elasticity of material of the members are same…

Q: The strain at a point is 780x10-s in the x, 400x10-6 in the y and -500x106 in the z direction.…

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

Q: The stress–strain diagram for a titanium alloy can be approximated by the two straight lines. If a…

A: Given data: Dimensions of the rectangular cross-section of the strut, b = 2 in and h = 3 in So, the…

Q: Determine the total strain energy of the steel beam shown in Figure 2. The cross section is…

Q: H.W.7 A rigid steel bar ABC is supported by three rods. There is no strain in the rods before load P…

Q: A strain gage is mounted to the outer surface of a thin-walled boiler. The boiler has an inside…

Q: A rigid steel bar AB is pinned at A and supported by two rods. There is no strain in the rods before…

Q: The state of strain on an element has components = -280(10-6), ɛ, = 120(10-6), Yæy = 180(10-6).…

A: Given data, εx=280(10-6) εy=120(10-6) γxy=180(10-6)

Q: Rigid bar ABCD is supported by two bars as shown. There is no strain in the vertical bars before…

A: The deflection in bar 2 is calculated as: δC=3300×10-6×1200=3.96 mm

Q: A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical…

A: Given data: ◆ The normal strain in the rod (1): ε1 = -1380 µm/m = -1380 × 10-6 m/m ◆ The gap in the…

Q: The principal plane stresses and associated strains in a plane at a point are s1 = 36 ksi, s2 = 16…

A: Given: The values of principal stresses are s1=36 ksi and s2=16 ksi. The values of strains are…

Q: In the following structure if the temperature increases by 20 °C, determine the normal stress in…

A: Given Data The increased temperature is: T=20°C The distance BD is: BD=400 mm The distance BF is:…

Q: H.W.7A rigid steel bar ABC is supported by three rods. There is no strain in the rods before load P…

A: Consider the diagram as shown below for the given system.

Q: A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of…

Q: A rectangular block is 7 cm long in the x-direction, 5 cm in the y-direction, and 9 cm long in the…

Q: H.W.2: The load P produces an axial strain of -1,800 ue in post (2). Determine the axial strain in…

Q: a) A thin strip of rubber-like material has an unstretched length of 345 mm. i. If it is stretched…

A: (a) To find: The average normal strain in the strip. Given: The upstretched length of material is…

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

Q: The Poisson ratio formula for an auxetic structure given in the figure is given as follows: H = 8…

A: Given Data Height of structure is : H=8 cm=80 mm Length is : L=4 cm=40 mm Angle is : α=50°…

Q: A rigid steel bar is supported by three rods, as shown in the figure. There is no strain in the rods…

Q: The wire BC has a diameter of 3.4 mm and the material has the stress-strain characteristics shown in…

A: Diameter of wire BC, d= 3.4 mm Length of wire BC, LBC= 1000 mm Length AB, LAB =1250 mm Length AD,…

Q: For the steel plate with the plane stress state shown. If E 200 GPa, v = 0.3 and a=12*10 /C. if this…

A: Given: The modulus of elasticity, E = 200 Gpa The Poisson ratio, ν = 0.3 The coefficient of thermal…

Q: 1. A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are Ex 0:40…

Q: A rigid steel bar ABC is supported by three rods made of steel [E=200 GPa]. There is no strain in…

Q: A high-density polyethylene [E = 128 ksi; α= 88 x 10-6/°F; υ = 0.4] bar is positioned between two…

A: Given: E = 128 ksi Coefficient of thermal expansion, α = 88×10-6 /°F Poisson's Ratio, υ = 0.4…

Question

A pipe is subjected to a tension force of P
= 45 kN. The pipe outside diameter is 41
mm, the wall thickness is 6.0 mm, and the
elastic modulus is E = 120 GPa. Determine
the normal strain in the pipe.
Select one:
a. 0.001263 mm/mm
b. 0.000535 mm/mm
c. 0.000568 mm/mm
d. 0.000794 mm/mm
O e. 0.001382 mm/mm
f. None

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
A pipe is subjected to a tension force of P = 70 kN. The pipe outside diameter is 32 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 180 GPa. Determine the normal strain in the pipe. P Select one: O a. 0.001263 mm/mm O b. 0.000535 mm/mm O c. 0.000568 mm/mm O d. 0.000794 mm/mm e. 0.001382 mm/mm O f. None
The strain in the x-direction at point A (shown in fig.) on the steel beam is measured and found to be ɛx = 139 x 106. The shear strain at point A is found to be yxY = R x 10° radians. The magnitude R is given by: (Take E= 204 GPa and Poisson's ratio =0.3). The cross-section of the beam is rectangular with depth 400mm and width 200mm respectively 100m 4ocmm 40om 600mnın 1000 mm 200mm
Find the value of strain stress 30 MPa Modulus of elasticity=65 MPa
= 2-Consider a 45° off-axis tensile test coupon. Three strain gages attached as shown below are reading el 0.00647, 2= -0.00324, and 3 = 0.008095 at stress level of ox=100 MPa. Determine the off-axis modulus of elasticity Ex the off-axis major Poisson's ratio vxy and coefficient of mutual influence of the second kind nxy,x 2 √²-01-² y 45° €2 0₂
A force P of 70 N is applied by a rider to the front hand brake of a bicycle(Pis the resultant of an evenly distributed pressure). As the hand brakepivots at A. a tension T develops in the 460-mm Ions; brake cable (Ae=1.075 mm²), which elongates by δ 6=0.214 mm. Find the normal stress 8and strain e in the brake cable.Brake cable, L = 460 mmHand brake pivot A
10/10 find the strain( €) in x-axis only . if .Poisson ratio=D0.25, E= 200 GPa 14 kN 10 kN 12 kN 15 mm 10 mm 20 mm
A force P of 70 N is applied by a rider to thefront hand brake of a bicycle (P is the resultant of anevenly distributed pressure). As the hand brake pivots atA, a tension T develops in the 460-mm long brake cable(Ae = 1.075 mm2 ), which elongates by δ = 0.214 mm.Find the normal stress d and strain in the brake cable.
A pipe is subjected to a tension force of P = 45 kN. The pipe outside diameter is 41 mm, the wall thickness is 6.0 mm, and the elastic modulus is E = 120 GPa. Determine the normal strain in the pipe.
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.4 lb/in.³ is the specific weight of the material, y = 3.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 19 in. is the length of the bar, and E= 24000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar. Part 1 Calculate the change in length of the bar due to its own weight. Answer: d = i x10-6 in.
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 0.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 8 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.
1-2-2 A force P of 70 N is applied by a rider to the front hand brake of a bicycle (P is the resultant of an evenly distributed pressure). As the hand brake pivots at A, a tension T develops in the 460-mm long brake cable (A, = 1.075 mm²) which elongates by 8 = 0.214 mm. Find normal stress and strain & in the brake cable. Brake cable, L= 460 mm PROB. 1.2-2 37.5 mm/A, Hand brake pivot A 50 mm -100 mm- P (Resultant of distributed pressure) Uniform hand brake pressure