In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x10-6 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm (1) A 100mm 300mm 6kN 400mm

In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x10-6 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm (1) A 100mm 300mm 6kN 400mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.2P: A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas....

See similar textbooks

Related questions

Q: A steel wire 10m long, hanging vertically, supports a load of 22kN. Neglecting the weight of the…

A: To solve this problem, we need to first find the diameter of wire based on allowable stress in the…

Q: QUESTION 3) Closed and open triangular section tubes are made of same materials are shown in figure.…

A: Given: Closed and open triangular section tubes are made of same materials areshown in figure. If…

Q: 1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A: In this question there are two different question. according our guidelines, I am giving the…

Q: Find the stresses at point C. -1.5 m 2.5 m 250 mm 125 mm 1.5 m 50 kN/m 50 mm 2 m 4m

A: Find the stresses at point C.

Q: The pipe shown in Fig a has an inner radius of 40 mm and an outer radius of 50 mm. If its end is…

A: Given Inner radius of pipe = 40 mm Outer radius of pipe = 50 mm To find The shear stress inner and…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: To find: The state of stress at point A on the cross section of pipe at section a-a. Given: The…

Q: H.W2: A rectangular column of sides 0.4m×0.35m, made of concrete, is used to support a compressive…

A: Data given- Rectangular column = 0.4 × 0.35 sides Compressive load = 1.5 MN Diameter of steel rod…

Q: Homework :-in the figure shown. Find the total deformation and the stress in each section if E is…

Q: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: If the principal stresses in a plane stress problem are ơ1 = 100 MPa, ơ2 = 40 MPa, the magnitude of…

A: Write the given values along with suitable variables.

Q: A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E…

Q: For the structure shown below, the shear stress in the pin at B is determined a MPa if it has a…

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

Q: Af D Find the stress in each cord of the system shown in fig. below if the cross section area of…

A: To find : The stress in each cord . Given data : The cross sectional area of cord A=450 mm2. The…

Q: Determine the principle stresses σ1, σ2, σ3 and their orientation φ, if σx, σy and σz are known as…

Q: At the ambient temperature, the A-36 steel pipe fits snugly between the two fuel tanks. When fuel…

A: Given: The change in length, δL = 4.6 mm The modulus of elasticity, E = 200 Gpa The length of pipe,…

Q: Ifthe gap between Cand the rigid wall at D is initially 0.13 mm as shown in Figure 1 and the…

A: Here, l1 = 650 mmd1 = 50 mmA1 = π4 d12 = 1963.5 mm2l2 = 610 mmd2 = 25 mmA2 = π4d22 = 490.9 mm2E =…

Q: The specification of a cylindrical vessel are as follows: D = 350 mm t = 12 mm P = 4.5 MPa Determine…

Q: 10/10FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70…

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400…

Q: 800 N D 120 N.m d = 8 cm 600 N Q / If the cross section of the femur can be approximated as a…

A: 1. Stress due to eccentric load of 800N P2 and 800N will create a momentMoment due to this…

Q: 3.5 m r= 0.6e-0.08y² y 0.6 m

Q: H.W.2 A 60 mm wide by 8 mm thick steel plate is connected column o a gusset plate by a 20 mm…

A: 1)-Normal stress on surface area:Agross=60mm×8mmAgross=480mm2

Q: 1: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

A: The normal stresses will be acting due the normal forces as well as bending moments on the rod. The…

Q: In a volume element with dimensions dx, dy, dz the negative y-face has a 2 MPa stress in the…

Q: The components of plane stresses at a critical point are shown in the following figure. Determine…

Q: The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of…

Q: 1. A 1.5-m long circular cross-sectioned bar with r = 1 cm is under a combination of bending moment…

A: DISCLAIMER FOR MULTIPART FROM BARTLEBYSince you have posted a question with multiple sub-parts, we…

Q: View Policies Current Attempt in Progress A typical stainless steel cylindrical vessel is shown. The…

A: Given data D = 48 in t = 0.75 in P = 1.1 ksi Find Hoop stress = ?

Q: For the given stress element, consider the magnitude for oA, OB, and t to be 15.0 MPa, 40.0 MPa, and…

Q: 1. A cylinder tankhas a maximum load of 2600 kg while the pressure is 2600 kpa. If the ultimate…

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: 04 It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN)…

Q: It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm…

Q: Arshadadhom shubber H.W. 2: A 60-mm-wide by 8-mm-thick steel plate is connected to a gusset plate by…

A: Given data, P= 70 kN L=60 mm d= 20 mm (pin diameter) t= 8 mm

Q: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: Given data diameter of shaft (d) = 80 mm maximum shear stress in shaft (τmax) = 63 MPa width of…

Q: It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN) mm…

Q: double-shear pin connections at Band D. All pins are 7 mm in diameter. a = 750 mm, b= 350 mm, h =…

Q: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

Q: 1. If o, = 20 ksi, o, = 10 ksi, and txy = 30 ksi, what is the absolute maximum shear stress for the…

A: Calculated absolute maximum shear stress.

Q: qo M h For the given system; a) Draw internal force diagrams and determine the most critical…

A: Consider horizontally forward & vertically upward force as (+)ve and horizontally backward &…

Q: The frame supports the triangular distributed load shown. Determine the normal and shear stresses at…

A: Reaction force acting ay point B is RB=900×32×3×13×13=450 N The cross section area is…

Q: Q4/ Thế normal stress applied due to the * :axial force 10 KN is 10 kN h-100 mm 2m 4m b-50 mm 20…

A: Find the normal stress.

Q: F2. F3 F1 L2 A pipe is subjected to loads as shown in figure. The outer and inner diameters of the…

A: Given: The inner diameter of pipe, d = 79 mm The outer diameter of pipe, D = 99.2 mm The force along…

Q: 1. A steel thick-walled cylinder has an inner diameter of 25mm and an outer diameter 110mm. The…

Q: Determine the equivalent state of stress on an element at the same point onented 30°…

Q: Determine the stress in each cord for the system shown in fig. below, if the cross section area of…

A: To find: The stress in each cord. Given: The area of the each cord is A=650 mm2. Formula used: The…

Question

In the following structure if the temperature increases by 20 °C, determine the normal stress in Links
(1) and (2).
E (GPa)
A (mm2)
a (1/°C)
11.9x10-6
Link 1
200
310
Link 2
70
620
22.5x106
500mm
350mm
B
to
A
100mm
300mm
(2)
6kN
400mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
The principal strains at a point on the aluminum fuselage of a jet aircraft are P1 = 780(10-6) and P2 = 400(10-6). Determine the associated principal stresses at the point in the same plane. Eal = 10(103) ksi, nal = 0.33.
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
Determine the maximum normal stress in the bar. The diameter is 1.5cm.F1 = 7KN F2 = 6KN F3 = 2KN F1 = 9KN
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 139°C. Determine the normal stress in the aluminum rod.
Indicate the points on the stress-strain diagram which represent the proportional limit and the ultimate stress.
Determine the principal stresses at points A and B of the cylinder. Consider: L = 70 mm; d = 20 mm; F = 12 kN; P = 15 kN; T = 800 Nm.
The normal strain measured on the outside surface of a spherical pressure vessel is 670 με.The sphere has an outside diameter of 1.20 m and a wall thickness of 10 mm, and it will befabricated from an aluminum alloy [E = 73 GPa;ν = 0.33]. Determine (a) the normal stress inthe vessel wall and (b) the internal pressure in the vesssel
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T1 = 60°F. Each rod has a diameter of 1.25 in. Determine the average normal stress in each rod if T2 = 400F, and also calculate the new length of the aluminum segment. Take aal = 13(10-6)>°F, Eal = 10(103) ksi, (sY)al = 40 ksi, acu = 9.4(10-6)>°F, (sY)cu = 50 ksi, and Ecu = 15(103) ksi
The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is